Mehmet Ipekoglu

Dr. Mehmet Ipekoglu

orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 January 2017 in Journal of Materials Research
Verified
Journal Article
Closed access
PDF file
MIMehmet Ipekoglu
Mehmet Ipekoglu
ANAmin Nekouyan
Amin Nekouyan
Onder AlbayrakOnder Albayrak
Onder Albayrak
SASabri Altintas
Sabri Altintas

4 February 2012 in Environmental Science and Pollution Research
Verified
Journal Article
Closed access
PDF file
EHErdem Hasret
Erdem Hasret
MIMehmet Ipekoglu
Mehmet Ipekoglu
SASabri Altintas
Sabri Altintas
NINursen A. Ipekoglu
Nursen A. Ipekoglu

1 November 2010 in Materials Technology
Verified
Journal Article
Closed access
MIMehmet Ipekoglu
Mehmet Ipekoglu
SAS. Altintas
S. Altintas

20 March 2022 in European Mechanical Science
Verified
Journal Article
Open access
PDF file
MIMehmet Ipekoglu
Mehmet Ipekoglu
HGHasan Gündüz
Hasan Gündüz
Onder AlbayrakOnder Albayrak
Onder Albayrak
In this study, linen and cotton fibers obtained from fabric waste were used as filler materials and polyethylene was used as matrix material to produce fiber reinforced polymer composites using injection molding. Use of fabric waste as filler material enables utilization of linen and cotton wastes while decreasing the amount of polyethylene used in the composites resulting in an environmentally friendly material. Prepared samples with varying content of linen and cotton wastes (5, 10 and 20 vol. %) were compared with each other and with polyethylene samples without any filler, based on their yield, tensile and fracture strengths, percent elongation and hardness values. Samples were also evaluated for their chip formation characteristics based on chip lengths at various machining speeds and examined for their visual appearance. Results indicated that linen waste fibers can be used to improve the strength of polyethylene based composites while cotton waste fibers can be utilized to enhance the elongation characteristics of the samples.

1 January 2022 in TURKISH JOURNAL OF CHEMISTRY
Verified
Journal Article
Open access
PDF file
EKElif Emil Kaya
Elif Emil Kaya
BEBurak Evren
Burak Evren
ZEZeynep Erdöl
Zeynep Erdöl
DEDuygu Eki̇nCi̇
Duygu Eki̇nCi̇
MIMehmet Ipekoglu
Mehmet Ipekoglu
SÖSi̇bEl Özenler
Si̇bEl Özenler
In this study, an abundant and eco-friendly photocatalytic material, Fe2O3 particles were synthesized by sonochemical method. Morphological and microstructural investigations of synthesized undoped and Ni, Co-doped Fe2O3 particles were performed. The effect of particle morphology and microstructure on its photocatalytic performance was further investigated. Comparative studies for evaluating particle crystallite sizes were conducted by Williamson-Hall (W-H) method and modified Debye-Scherrer (MDS). Crystallite sizes and lattice strains of Fe2O3 induced by process parameters were calculated by W-H method based on uniform deformation model (UDM). The crystallite sizes of the synthesized powders were calculated in the range of 200 nm and 76 nm by Williamson-Hall analysis. In addition to structural investigation, dislocation density of the synthesized particles was calculated by Williamson-Smallman relation. Afterwards, photocatalytic performance of Fe2O3 particles was investigated in detail. The photodegradation of methylene blue solutions in the presence of light in 20 min with samples 3,4, and 5 in 20 min were 0.937, 0.896, and 0.855, respectively. Moreover, the photodegradation of methylene blue solution with sample 5 for 15, 30, and 45 min were 0.9, 0.828, and 0.757, respectively. A photocatalytic activity of 24.25% has been observed under optimum conditions for the time interval of 45 min.

15 November 2017 in Materials Testing
Verified
Journal Article
Closed access
MIMehmet Ipekoglu
Mehmet Ipekoglu
OEOnur Erbas
Onur Erbas
HHHamad Ul Hassan
Hamad Ul Hassan
Being one of the most commonly applied sheet metal forming processes in automotive industry, deep drawing technologies are challenged by the concerns of global warming for higher fuel economy requirements in the recent years. To reduce the weight of the vehicles in order to obtain fuel economy, lighter and safer materials are used in automotive industry. Aluminum alloys, due to their low density compared to steels, are an important group of materials, in particular for lightweight construction of vehicles. In this study, two different aluminum alloys, namely AA5754-H22 and AA6061-T6, are evaluated for their potential use in nonload bearing applications in commercial vehicles by comparing their deep drawability characteristics. For this purpose, they are characterized by uniaxial tensile and Nakajima tests. In the next step, the deep drawing experiments are performed under different levels of blankholder force. The distance of the cup center to the edge of the die is also evaluated to investigate ... Kurzfassung Als einer der am häufigsten angewandten Metallblechumformprozesse im Fahrzeugbau bestehen bei den Tiefziehtechniken Herausforderungen bezüglich des Klimawandels in Bezug auf höhere Treibstoffwirtschaftlichkeitsanforderungen in den letzten Jahren. Um das Gewicht der Fahrzeuge für eine bessere Treibstoffwirtschaftlichkeit zu reduzieren, werden leichtere und sichere Werkstoffe in der Automobilindustrie verwendet. Aufgrund ihrer geringeren Dichte im Vergleich zu Stählen stellen Aluminiumlegierungen eine wichtige Werkstoffgruppe dar, insbesondere für den Fahrzeugleichtbau. In der diesem Beitrag zugrunde liegenden Studie wurden zwei verschiedene Aluminiumlegierungen, und zwar AA5754-H22 und AA6061-T6, bezüglich ihres potentiellen Gebrauchs für nicht lasttragende Anwendungen in kommerziellen Fahrzeugen evaluiert, indem ihre Tiefzieheigenschaften verglichen wurden. Zu diesem Zweck wurden sie mittels einachsiger Zugversuche und sogenannter Nakajima-Tests charakterisiert. Im nächsten Schritt wurden die ...