Piotr Malenta

Dr. Piotr Malenta

orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 June 2020 in Eksploatacja i Niezawodność – Maintenance and Reliability
Verified
Journal Article
Closed access
Andrzej KosuckiAndrzej Kosucki
Andrzej Kosucki
Lukasz StawinskiLukasz Stawinski
Lukasz Stawinski
PMPiotr Malenta
Piotr Malenta
JZJakub Zaczyński
Jakub Zaczyński
Justyna SkowrońskaJustyna Skowrońska
Justyna Skowrońska
The article presents the numerical investigation of the overhead crane’s energy consumption. The analysis is based on the hybrid model of the crane consisting of numerical model of drive mechanisms as bridge, trolley, hoist and also experimentally measured power consumption of each control unit. The numerical model was verified experimentally on the real crane. The investigation focuses on analyzing the energy consumption of the overhead crane in relation both to the travelled distance and also for the lifting and lowering heights of a suspended payload. Particular attention was paid on the cases straightly related to the hoist, as a main factor of improvements in the energetic efficiency of the overhead crane. Energy consumption was investigated for a variety of magnitudes of transported mass

23 April 2025 in Energies
Verified
Journal Article
Open access
PDF file
Lukasz StawinskiLukasz Stawinski
Lukasz Stawinski
Andrzej KosuckiAndrzej Kosucki
Andrzej Kosucki
Justyna SkowrońskaJustyna Skowrońska
Justyna Skowrońska
PMPiotr Malenta
Piotr Malenta
This article addresses the current issue of energy consumption in the hydraulic drive systems of working machines, with particular emphasis on elevators. This paper describes the results of experimental comparative research and estimation of energy and time consumption for two drive systems of a hydraulic indirect elevator. The purpose of this article is to compare the energy consumption of a typical multi-valve system (MV) system with that of an innovative new electro-hydraulic drive (EHD) system with a variable speed pump. The EHD system uses a frequency converter with an energy recovery module to control the speed of the car in both directions and the return of potential energy during the lowering cycle. The comparison of these drive systems was performed under the same conditions, realizing the same elevator work cycles. This paper proposes methods for estimating the energy consumption of an MV system based on measurement data collected during an experiment. The results indicate that the EHD system was less energy-intensive, even at below 60%. The smaller the load mass, the shorter the operating time of the EHD system compared to the MV system. The introduced coefficients defining the energy consumption per unit of mass and payload displacement showed more than twice the decrease in energy demand during lifting and energy recovery possibility during lowering. The EHD system provides the same coefficient values regardless of the distance traveled, which makes it a predictable system, in contrast to the MV system, especially during lowering cycles. The benefits of the EHD also include a less complex hydraulic system (elimination of most valves).

21 September 2017 in Eksploatacja i Niezawodność – Maintenance and Reliability
Verified
Journal Article
Closed access
Andrzej KosuckiAndrzej Kosucki
Andrzej Kosucki
PMPiotr Malenta
Piotr Malenta
Lukasz StawinskiLukasz Stawinski
Lukasz Stawinski
SHSławomir Halusiak
Sławomir Halusiak

27 June 2016 in Eksploatacja i Niezawodność – Maintenance and Reliability
Verified
Journal Article
Closed access
Andrzej KosuckiAndrzej Kosucki
Andrzej Kosucki
PMPiotr Malenta
Piotr Malenta

19 August 2022 in ISA Transactions
Verified
Journal Article
Open access
Andrzej KosuckiAndrzej Kosucki
Andrzej Kosucki
PMPiotr Malenta
Piotr Malenta
MOMaciej Olejnik
Maciej Olejnik
Lukasz StawinskiLukasz Stawinski
Lukasz Stawinski
A simplified inverter-motor stator system model is presented in the paper. The model is based on elementary dynamic blocks described by differential equations. The paper presents the results of research aimed at verifying the model on different devices with different types of inverters and motors. Model accuracy coefficients have been developed for all examined cases, confirming the high conformity of the model to the measured speeds and torques of asynchronous motors. The model was also used to simulate the operation of a drive system with a synchronous motor, obtaining high compliance of speed and torque mapping. The presented cases of verification of a simplified model confirm the possibility of using it to model different devices fed by frequency inverters, controlled both manually and automatically. The presented model, using simple description, ensures high accuracy of speed and torque mapping. It should be emphasized that most parameters in the presented model are calculated for motors and inverters based on data sheets.(c) 2023 The Authors. Published by Elsevier Ltd on behalf of ISA.This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/).

10 July 2026 in Eksploatacja i Niezawodność – Maintenance and Reliability
Verified
Journal Article
Open access
PDF file
Lukasz StawinskiLukasz Stawinski
Lukasz Stawinski
PGPaweł Grzejszczyk
Paweł Grzejszczyk
PMPiotr Malenta
Piotr Malenta
Justyna SkowrońskaJustyna Skowrońska
Justyna Skowrońska
Andrzej KosuckiAndrzej Kosucki
Andrzej Kosucki
This paper investigates the influence of hydraulic oil temperature on the performance of a piston pump. The primary objective of the study was to determine variations in volumetric efficiency by developing operational maps under different thermal conditions, system pressures, and rotational speeds. The experiments were conducted on a laboratory test stand equipped with a fixed‑displacement piston pump driven by a electric motor. Measurement signals were processed using LabVIEW software, enabling the generation of efficiency maps across a wide operating range. The results highlight the strong dependence of pump efficiency on the temperature of the working fluid, particularly at low speeds and elevated pressures. The developed maps provide valuable insights into the operating boundaries of the pump, offering practical guidance for both system design and operational planning. The findings emphasize that temperature‑dependent characteristics constitute a crucial source of information for ensuring high efficiency, durability, and reliability of hydraulic systems employing piston pumps.