The wet-laid hybrid nonwoven process can produce affordable carbon fiber-reinforced thermoplastic (CFRTP) because of its process simplicity, which can promote the application of CFRTP products in automobile weight reduction. The wet-laid hybrid nonwoven process involves two procedures, mainly: prepare preforms by a papermaking-like process and heat-molding compression. The parameters of heat-molding compression affect the quality of CFRTP directly, but there are not enough researches focusing on the effects of heat-molding compression parameters. This study aims to optimize the wet-laid hybrid nonwoven process to prepare recycled CFRTP. A proper carbon fiber content was determined firstly. Then, response surface methodology was used to optimize the heat-molding compression parameters. The effects of fiber length on composite properties were also investigated. The results showed that the fiber content of 30 wt% was the most suitable. The optimized heat-molding conditions were temperature, pressure, and time of 190°C, 2 MPa, and 10 min, respectively, leading to the lowest void content of 0.9%. CFRTP comprising carbon fibers with a length of 6 mm had the best properties, with the tensile strength of 59.34 MPa and flexural strength of 145.91 MPa.
23 March 2023 in Journal of Reinforced Plastics and Composites
This paper introduces three different methods to improve the interfacial shear strength (IFSS) of PP/CF nonwoven composites: (A) mixing maleic anhydride-grafted-PP (MAPP) powder into polypropylene/carbon fiber (PP/CF) nonwoven preform, (B) grafting MAPP onto polydopamine-coated-CF (PCF) utilizing esterification reaction, and (C) coating ethylene–glycidyl methacrylate (E-GMA) copolymer onto CF through solution dipping. First, scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectra, and X-ray photoelectron spectroscopy (XPS) results over modified CFs show that the MAPP and E-GMA were delivered onto CF. Surface Chemistry analysis validated the esterification between MAPP and PCF. Second, the tensile test and SEM observation of composites’ tensile fracture region confirmed the improved interfacial adhesion. Tensile strength was improved by 42.5%, 44.6%, and 49.8% by Method A, B, and C, respectively. Finally, the Bowyer-Bader methodology estimated the IFSS improvement of 352%, 161%, and 136% produced by Method A, B, and C, respectively.
A kind of superhydrophobic copper surface with micro-nanocomposite structure has been successfully fabricated by employing a silk-screen printing aided electrochemical machining method. At first silk-screen printing technology has been used to form a column point array mask, and then the microcolumn array would be fabricated by electrochemical machining (ECM) effect. In this study, the drop contact angles have been studied and scanning electron microscopy (SEM) has been used to study the surface characteristic of the workpiece. The experiment results show that the micro-nanocomposite structure with cylindrical array can be successfully fabricated on the metal surface. And the maximum contact angle is 151° when the fluoroalkylsilane ethanol solution was used to modify the machined surface in this study.
Timely detection and treatment of moisture anomalous regions in grain storage facilities is crucial for preventing mold growth, germination, and pest infestation. To locate these regions, this paper presents a novel anomalous moisture region localization algorithm based on the delay-multiply-and-sum (DMAS) beamforming techniques, including the design of an effective spatial arrangement of electromagnetic wave transmitters and receivers, along with comprehensive testing of detectable regions and experimental validation of anomaly localization across varying moisture levels and positions within grain piles. Following initial localization using the proposed algorithm, the study introduces a reliability assessment method for unknown samples based on the signal-to-mean ratio (SMR) value and compares the region of maximum response intensity with that of maximum connected domain volume. The system demonstrated successful localization of a 7 cm × 7 cm × 7 cm region with 15.4% moisture content within a cubic experimental bin containing 10.5% moisture content long-grained rice, achieving an average recall accuracy exceeding 50%. The proposed method presents rapid detection capabilities and precise localization, showing potential for moisture content evaluation of anomalous regions and practical applications in grain storage monitoring systems.
PP/CF wet-laid nonwoven composites have potential application in automotive secondary structural parts, but their long-term service behavior needs clarification. This paper investigated the effect of CF content, load, and interfacial enhancement on short-term creep behavior of the composite and plotted a master creep curve to study the long-term creep behavior. Short-term tests showed that creep resistance peaked at 30 vol% CF, higher loads reduced resistance, and interfacial enhancement improved it. The Findley and Burgers models fitted short-term curves well, with Burgers parameters reflecting intrinsic creep behavior. Creep master curves (reference temperature of 30 °C) of 30 vol% CF composites showed no rupture, indicating good long-term creep performance.