Jianbiao Du

Jianbiao Du


Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 April 2025 in Buildings
Verified
Journal Article
Open access
PDF file
WQWei Qi
Wei Qi
NFNa Fu
Na Fu
JDJianbiao Du
Jianbiao Du
XWXianliang Wang
Xianliang Wang
Tengfei WangTengfei Wang
Tengfei Wang
Red-bed mudstone from civil excavation is often treated as waste due to its poor water stability and tendency to disintegrate. This study proposes a sustainable approach for its utilization in controlled low-strength material (CLSM) by blending it with cement and water. Laboratory tests evaluated the fresh properties (i.e., flowability, bleeding rate, setting time, and subsidence rate) and hardened properties (i.e., compressive strength, drying shrinkage, and wet–dry durability) of the CLSM. The analysis focused on two main parameters: cement-to-soil ratio (C/S) and water-to-solid ratio (W/S). The results show that increasing W/S significantly improves flowability, while increasing C/S also contributes positively. Flowability decreased exponentially over time, with an approximately 30% loss recorded after 3 h. Bleeding and subsidence rates rose sharply with higher W/S but were only marginally affected by C/S. To meet performance requirements, W/S should be kept below 52%. In addition, the setting times remained within 24 h for all mixtures tested. Compressive strength showed a negative correlation with W/S and a positive correlation with C/S. When C/S ranged from 8% to 16% and W/S from 44% to 56%, the compressive strengths ranged from 0.3 MPa to 1.22 MPa, meeting typical backfilling needs. Drying shrinkage was correlated positively with water loss, and it decreased with greater C/S. Notably, cement’s addition significantly enhanced water stability. At a C/S of 12%, the specimens remained intact after 13 wet–dry cycles, retaining over 80% of their initial strength. Based on these findings, predictive models for strength and flowability were developed, and a mix design procedure was proposed. This resulted in two optimized proportions suitable for confined backfilling. This study provides a scientific basis for the resource-oriented reuse of red-bed mudstone in civil engineering projects.

21 August 2026 in Buildings
Verified
Journal Article
Open access
PDF file
LPLingying Peng
Lingying Peng
YCYong Cao
Yong Cao
WQWei Qi
Wei Qi
GYGe Yang
Ge Yang
XLXianbo Li
Xianbo Li
Tengfei WangTengfei Wang
Tengfei Wang
Loess is highly water-sensitive and collapsible, and its conventional use as backfill in road and railway infrastructure may lead to settlement and deformation after wetting. Converting excavated loess into controlled low-strength material (CLSM) provides an alternative for backfilling; however, its engineering performance is strongly dependent on the water-to-solids ratio (W). In field construction, variations in the natural moisture content of loess cause the actual W to deviate from its design value, whereas conventional CLSM mix designs generally assume a fixed W, which may result in insufficient flowability or strength under actual field conditions. A Box–Behnken design was first employed to investigate the effects of the cement-to-soil ratio (C), water-to-solids ratio (W), and polycarboxylate superplasticizer content (P) on flowability (f), bleeding rate (Bᵥ), wet density (ρ), and 28-day compressive strength (qᵤ), based on which regression-based predictive models were developed. The sequential least squares programming (SLSQP) algorithm was then used to optimize mix proportions for backfilling behind abutments, culverts, and retaining walls and for subgrade backfilling. The optimization minimized the material cost per unit volume while requiring all performance indicators to satisfy the specified criteria under variations in W (ΔW = 0%, ±1%, ±2%, and ±3%). The results show that W is the dominant factor governing f, Bᵥ, and ρ, whereas C has the greatest influence on qᵤ. Increasing P markedly improves f but also increases Bᵥ. For backfilling behind abutments, culverts, and retaining walls, when the mean field soil moisture content is overestimated and the actual W is consequently lower than its design value, the mix optimized for ΔW = −3% satisfies the flowability criterion even when the measured flowability is up to 21.3 mm below the design value because of the lower actual soil moisture content. Conversely, when the mean field soil moisture content is underestimated and the actual W exceeds its design value, the mix optimized for ΔW = +3% satisfies the compressive-strength criterion even when the measured strength is up to 0.09 MPa below the design value because of the higher actual soil moisture content. Accounting for possible variations of up to ±3% in the water-to-solids ratio under field conditions, the optimal mix proportions are C13.14W37.64P0.069 for backfilling behind abutments, culverts, and retaining walls and C15.00W34.28P0.097 for subgrade backfilling. These findings provide a basis for the performance control and mix design of loess-based CLSM subjected to variations in the water-to-solids ratio.

11 June 2026 in Materials
Verified
Journal Article
Open access
PDF file
ACAiping Chen
Aiping Chen
YCYong Cao
Yong Cao
WQWei Qi
Wei Qi
LSLihong Shu
Lihong Shu
FLFeiyang Liu
Feiyang Liu
Tengfei WangTengfei Wang
Tengfei Wang
To enhance the strength and water stability of stabilized expansive soil, this study investigates the use of cement, montmorillonite adsorption modifier (MAM), and their composite system. Laboratory tests evaluated compaction characteristics, swell–shrink behavior, and mechanical performance. The results show that MAM more effectively regulates compaction by reducing optimum water content and increasing maximum dry density; 6% MAM increases maximum dry density by ≈0.04 g/cm3 and reduces optimum water content by ≈2%. In terms of swell–shrink behavior, MAM reduces both swelling and linear shrinkage more effectively than cement. The incorporation of 5% MAM reduces the free swelling ratio by 40% and the equilibrium moisture absorption by 2.7%, lowering the swelling classification to non-expansive. Furthermore, 5% MAM decreases the unloaded and loaded swelling ratio by 14.7% and 5%, respectively, while increasing MAM from 2% to 6% further reduces linear shrinkage by 1.12%. Cement significantly enhances compressive strength, with 7–28 d values reaching 2.2–2.7 times those of untreated soil at 9% content; however, its water stability under wet–dry cycles is limited. In contrast, the cement–MAM composite system achieves balanced improvement by simultaneously suppressing swelling and enhancing both strength and water stability. These findings provide a reference for the treatment and engineering application of expansive soils.