With the increasing demand for multidirectional vibration measurements, traditional triaxial accelerometers cannot achieve vibration measurements with high sensitivity, high natural frequency, and low cross-sensitivity simultaneously. Moreover, for piezoresistive accelerometers, achieving pure axial deformation of the piezoresistive beam can greatly improve performance, but it requires the piezoresistive beam to be located in a specific position, which inevitably makes the design more complex and limits the performance improvement. Here, a monolithically integrated triaxial high-performance accelerometer with pure axial stress piezoresistive beams was designed, fabricated, and tested. By controlling synchronous displacements at both piezoresistive beam ends, the pure axial stress states of the piezoresistive beams could be easily achieved with position independence without tedious calculations. The measurement unit for the z-axis acceleration was innovatively designed as an interlocking proof mass structure to ensure a full Wheatstone bridge for sensitivity improvement. The pure axial stress state of the piezoresistive beams and low cross-sensitivity of all three units were verified by the finite element method (FEM). The triaxial accelerometer was fabricated and tested. Results showing extremely high sensitivities (x axis: 2.43 mV/g/5 V; y axis: 2.44 mv/g/5 V; z axis: 2.41 mV/g/5 V (without amplification by signal conditioning circuit)) and high natural frequencies (x/y axes: 11.4 kHz; z-axis: 13.2 kHz) were obtained. The approach of this paper makes it simple to design and obtain high-performance piezoresistive accelerometers.
The development of micro-electro-mechanical system (MEMS) alkali metal vapor cells offers the potential for the batch fabrication of micro-quantum sensors for atomic clocks, atomic magnetometers and atomic gyroscopes. The sealing of MEMS vapor cells is traditionally achieved by anodic bonding. However, high-temperature and high direct-voltage conditions during anodic bonding adversely affect the performance of the vapor cell. In this study, a fabrication method based on ultrafast laser welding integrated with a microfabrication process was developed for MEMS alkali metal vapor cells, and the energy-coupling mechanism of welding was analyzed. This method confined high temperatures to a localized area during laser welding. The cross-sections of the welding samples were analyzed, the element distribution was characterized, and the results showed that this method achieved high-strength sealing. Additionally, a platform for alkali metal injection and buffer gas charging was developed to enable the fabrication of MEMS vapor cells with ultrafast laser welding. The MEMS vapor cells were tested using absorption spectra, and the leakage rate under high-temperature vacuum conditions proved that high hermeticity could be achieved by ultrafast laser welding. Finally, MEMS vapor cells were used to fabricate a single-beam magnetometer, and its measurement sensitivity was determined experimentally. This process provides a new method for the efficient fabrication of MEMS vapor cells.
Recording moving magnetoencephalograms (MEGs ), in which a person’s head can move freely as the brain’s magnetic field is recorded, has been a key subject in recent years. Here, we describe a method based on an optically pumped atomic co-magnetometer (OPACM) for recording moving MEGs. In the OPACM, hyper-polarized nuclear spins produce a magnetic field that blocks the background fluctuation low-frequency magnetic field noise while the rapidly changing MEG signal is recorded. In this study, the magnetic field compensation was studied theoretically, and we found that the compensation is closely related to several parameters such as the electron spin magnetic field, nuclear spin magnetic field, and holding magnetic field. Furthermore, the magnetic field compensation was optimized based on a theoretical model . We also experimentally studied the magnetic field compensation and measured the responses of the OPACM to different magnetic field frequencies. We show that the OPACM clearly suppresses low-frequency (under 1 Hz) magnetic fields. However, the OPACM responses to magnetic field frequencies around the band of the MEG. A magnetic field sensitivity of 3 fT/Hz1/2 was achieved. Finally, we performed a simulation of the OPACM during utilization for moving MEG recording. For comparison, the traditional compensation system for moving MEG recording is based on a coil that is around 2 m in dimension , while our compensation system is only 2 mm in dimension .
5 October 2023 in Journal of Materials Research and Technology
Microfabricated alkali metal vapor cells are the core components for miniaturizing quantum devices , such as atomic clocks, atomic gyroscopes, and atomic magnetometers . Alkali metals are prone to thermal migration at the bonding interface during the sealing of the vapor cell, which leads to bonding failure. In this study, a non-isothermal anodic bonding process based on plasma activation was developed to achieve high-strength bonding at low temperatures using the temperature gradient to keep the alkali metal away from the bonding interface. This procedure eliminates interference from the alkali metal and significantly increases the success rate of anodic bonding of vapor cells. Simulation results for the temperature field and the residual stresses during anodic bonding demonstrate that the procedure is theoretically feasible. The effect of plasma treatment on the contact angle and roughness of the bonding surface revealed a mechanism for improving the bond strength . In addition, the construction of an integrated processing platform made it possible to perform non-isothermal anode bonding, injection of alkali metal, filling of inert gases, and recovery and recycling of noble gases. The high strength and good hermeticity of the bonding interface were demonstrated by the bond strength, cross-sectional high-resolution transmission electron microscopy observations, and leakage rate tests. Finally, the absorption spectrum and free-induction decay signal of the fabricated vapor cell were measured.