Chenliang Wu

Dr. Chenliang Wu


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 March 2018 in Coatings
Verified
Journal Article
Open access
PDF file
HWHaiyang Wang
Haiyang Wang
SZSong Zhang
Song Zhang
CZChunhua Zhang
Chunhua Zhang
CWChenliang Wu
Chenliang Wu
JZJingbo Zhang
Jingbo Zhang
Adil Othman AbdullahAdil Othman Abdullah
Adil Othman Abdullah
Fe-based coatings with high V and Cr content were obtained by laser cladding using Fe-based powder with different Cr3C2 and FeV50 content. The results showed that Fe-based coatings were uniform and dense. The constituent phases were mainly composed of α-Fe solid solution with the increase of Cr3C2 and FeV50, γ-Fe and V8C7 phases were achieved. The microstructure of the coatings exhibited a typical dendrite structure. The concentration of C, V and Cr were saturated in dendritic areas, and the other alloying elements were mainly dissolved in the interdendritic areas. The hardness and wear resistance of Fe-based coatings were enhanced with the Cr3C2 and FeV50 addition. The specimen with 15% Cr3C2 and 16% FeV50 had the highest hardness of 66.1 ± 0.6 HRC, which was 1.05 times higher than the sample with 4.5% Cr3C2 and 5% FeV50, and the wear resistance of the former was three times greater than the latter.

16 October 2023 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
FJF. Jin
F. Jin
SZSong Zhang
Song Zhang
CWChenliang Wu
Chenliang Wu
CZC. H. Zhang
C. H. Zhang
XSX. Y. Sun
X. Y. Sun
XBX. L. Bai
X. L. Bai

1 September 2023 in Materials Science and Technology
Verified
Journal Article
Closed access
HZH. F. Zhang
H. F. Zhang
SZSong Zhang
Song Zhang
CWChenliang Wu
Chenliang Wu
CZC. H. Zhang
C. H. Zhang
XBX. L. Bai
X. L. Bai
JCJ. Chen
J. Chen
The WC-Co composite coating was prepared on SS 316L by plasma arc welding technology. The microstructure, phase composition, and microhardness of the WC-Co composite coating were thoroughly studied. The corrosion behaviour including electrochemical corrosion, cavitation erosion, and erosion corrosion was tested. The results showed that the WC-Co coating exhibited a good metallurgical bond with the substrate. The average microhardness of the WC-Co coating reached 1785 HV, which was 9.4 times that of the SS 316L. The corrosion current density of the WC-Co composite coating was one order of magnitude lower than that of the substrate. Meanwhile, the cumulative mass loss of cavitation erosion and erosion corrosion of the WC-Co composite coating was much lower than that of the SS 316L.

10 May 2025 in Materials
Verified
Journal Article
Open access
PDF file
RHRenjie Huo
Renjie Huo
ZWZheying Wang
Zheying Wang
MWM. S. Wang
M. S. Wang
RWRui Wang
Rui Wang
SZSong Zhang
Song Zhang
JCJiang Chen
Jiang Chen
The influence of heat input (HI) on the microstructure, microhardness, electrochemical corrosion performance of cold metal transfer additively manufactured (CMTAM) nickel–aluminum bronze alloys was investigated. The nickel–aluminum bronze exhibited an α-Cu austenite matrix with minor γ2-Cu9Al4 and κ phases. As HI increased, the microstructure coarsened progressively. Electron backscatter diffraction (EBSD) analysis revealed that with increasing HI, the grain size gradually increased and the Schmid factor increased. Consequently, the microhardness declined from 198.3 HV to 171.7 HV. The decrease in microhardness with increasing heat input is primarily attributed to the grain coarsening and the coarsening and uneven distribution of the κ phase. As the heat input (HI) increased from 243.8 J/mm to 644.7 J/mm, the corrosion current density rose significantly from 2.56 ± 0.04 μA/cm2 to 7.52 ± 0.07 μA/cm2. This result indicates a marked deterioration in the material’s corrosion resistance. This phenomenon can be attributed to the grain coarsening and the distribution of Al solute within the microstructure. The CMTAM nickel–aluminum bronze alloys hold significant potential for enhancing the reliability and long-term protection of marine engineering equipment.

20 June 2023 in Journal of Thermal Spray Technology
Verified
Journal Article
Closed access
PDF file
HZH. F. Zhang
H. F. Zhang
SZSong Zhang
Song Zhang
CWChenliang Wu
Chenliang Wu
CZC. H. Zhang
C. H. Zhang
XBX. L. Bai
X. L. Bai
JCJ. Chen
J. Chen

25 July 2019 in Coatings
Verified
Journal Article
Open access
PDF file
WZWeian Zong
Weian Zong
SZSong Zhang
Song Zhang
CZChunhua Zhang
Chunhua Zhang
CWChenliang Wu
Chenliang Wu
JZJingbo Zhang
Jingbo Zhang
Adil Othman AbdullahAdil Othman Abdullah
Adil Othman Abdullah
To obtain the wear-resistant camshaft with surface rigidity and core toughness and improve the service life of camshaft, wear-resistant Fe-based alloy gradient material was prepared by laser melt deposition. The traditional camshaft was forged by 12CrNi2V. In this paper, four types of wear-resistant Fe-based powders were designed by introducing various content of Cr3C2 and V-rich Fe-based alloy (FeV50) into stainless steel powder. The results showed that the gradient materials formed a satisfactory metallurgical bond. The composition of the phases was mainly composed of α-Fe, Cr23C6, and V2C phases. The increasing of Cr3C2 and FeV50 led to transform V2C into the V8C7. The microstructures were mainly cellular dendrite and intergranular structure. Due to the addition of Cr3C2 and FeV50, the average microhardness and wear resistance of gradient materials were significantly better than that of 12CrNi2V. The sample with 8% V had the highest microhardness of 853 ± 18 HV, which was 2.6 times higher than that of 12CrNi2V. The sample with 6% V had the best wear resistance, which was 21 times greater than that of 12CrNi2V.