Synthetic aperture radar (SAR) remote sensing configurations are able to provide continuous measurements on global scales sensitive to the vertical structure of forests with a high spatial and temporal resolution. Furthermore, the development of tomographic SAR techniques allows the reconstruction of the three-dimensional (3-D) radar reflectivity opening the door for 3-D forest monitoring. However, the link between 3-D radar reflectivity and 3-D forest structure is not yet established. In this sense, this paper introduced a framework that allows a qualitative and quantitative interpretation of physical forest structure from tomographic SAR data at L-band. For this, forest structure is parameterized into a set of a horizontal and a vertical structure index. From inventory data, both indices can be derived from the spatial distribution and the dimensions of the trees. Similarly, two structure indices are derived from the 3-D spatial distribution of the local maxima of the reconstructed 3-D radar reflectivity profiles at L-band. The proposed methodology is tested by means of experimental tomographic L-band data acquired over the temperate forest site of Traunstein in Germany. The obtained horizontal and vertical structure indices are validated against the corresponding estimates obtained from inventory measurements and against the same indices derived from the vertical profiles of airborne Lidar data. The high correlation between the forest structure indices obtained from these three different data sources (expressed by correlation coefficients between 0.75 and 0.87) indicates the potential of the proposed framework.

The aim of this paper is to compare L- and P-band vertical backscattering profiles estimated by means of synthetic aperture radar (SAR) tomography and full light detection and ranging (lidar) waveforms in terms of their ability to distinguish different tropical forest structure types. The comparison relies on the unique DLR F-SAR and NASA Land, Vegetation and Ice Sensor (LVIS) lidar datasets acquired in 2016 in the frame of the AfriSAR campaign. In particular, F-SAR and LVIS data over three different test sites complemented by plot field measurements are used. First, the SAR and lidar three-dimensional (3-D) datasets are compared and discussed on a qualitative basis. The ability to penetrate into and through the canopy down to the ground is assessed at L- and P-band in terms of both the ground-to-volume power ratio and the performance to estimate the location of the underlying ground. The effect of polarimetry on the visibility of the ground is discussed as well. Finally, the 3-D measurements for each configuration are compared with respect to their ability to derive physical forest structure descriptors. For this, vertical structure indices derived from the volume-only 3-D radar reflectivity at L- and P-band and from the LVIS profiles are compared against each other as well as against plot-derived indices.

A two-layer model composed by ground and volume contributions has been proven suitable to describe the 3-D backscattering signatures of forest scenarios in a number of experiments. Under this hypothesis, the purpose of this letter is to investigate how synthetic aperture radar tomography (TomoSAR) can be used to estimate ground and volume polarimetric covariances and with which performance. An algorithm which is able to overcome the intrinsic ambiguity in the estimation problem is proposed, and it is shown to be a reliable alternative to the poorly performing full-rank Capon beamformer for estimating the ground polarimetric covariances. This performance improvement can be achieved, for instance, if an a priori knowledge of the ground topography (or an accurate estimate of it) is available. This analysis is carried out by processing an L-band TomoSAR stack acquired by the DLR’s E-SAR sensor over the temperate forest site of Traunstein.

Model-based forest height inversion from Pol-InSAR data relies on the realistic parameterization of the underlying (vertical) radar reflectivity function. In the context of interferometric TanDEM-X measurements - especially in the global single pol DEM mode - this is not possible due to the limited dimensionality of the observation space. In order to overcome this, the use of lidar waveforms to directly approximate the TanDEM-X reflectivity is proposed. This allows the forest height estimation from a single, single polarimetric, bistatic TanDEM-X acquisition. In order to extend the proposed lidar-supported inversion schema to areas only partially covered or sampled by (waveform) lidar measurements, the use of a “mean” (vertical) reflectivity profile is further proposed. This “mean” reflectivity profile is defined by means of the eigenfunctions of the available set of lidar waveforms. Both approaches are demonstrated and validated using TanDEM-X and airborne waveform lidar data acquired in the framework of the AfriSAR 2016 campaign over the Lopé National Park, in Gabon.

The present study addresses the development, implementation and validation of a forest height mapping scheme based on the combination of TanDEM-X interferometric coherence and GEDI waveform measurements. The very general case where only a single polarisation TanDEM-X interferogram, a set of spatially discrete GEDI waveform measurements and no DTM are available is assumed. The use of GEDI waveforms to invert the TanDEM-X interferometric measurements is described together with a set of performance criteria implemented to ensure a certain performance quality. The emphasis is set on developing a methodology able to invert forest height at large scales. Combining 595 TanDEM-X scenes and about 15 million GEDI waveforms, a spatially continuous 25 m resolution forest height map covering the whole of Tasmania Island is achieved. The derived forest height map is validated against an airborne lidar-derived canopy height map available across the whole island.

Prior to any processing of multibaseline (MB) synthetic aperture radar (SAR) data stacks, a MB phase calibration is necessary to compensate for phase contributions due to platform motions and/or atmospheric propagation delays. Classical calibration methods rely on the detection of point-like scatterers. However, especially in natural scenarios, their final calibration performance could be impaired by the nature of the scattering and by the typical low number of baselines. In this paper, we propose a calibration method based on the minimization of the entropy of the vertical profile of the backscattered power. This allows to potentially exploit the MB SAR signal independently of the nature of the scattering. The proposed method has been tested by processing simulated and real airborne datasets of a forest stand.