By using a carrier-based pulse width modulation, this paper presents a developed phase-shift space vector modulation strategy for a nine-switch inverter to overcome one of major drawbacks, i.e., output voltage and current distortion. This is due to the crossover of modulating waves per phase based on the different phase-shift angle between dual terminals. The proposed strategy done by mathematical algorithms based on the critical operating point principle accomplishes in the wide range of phase-shift conditions that contribute in both common- and difference-frequency modes with its expediency of uncomplicated computation and handy implementation. Even more, the identical and nonidentical modulation index techniques are wholly brought up. The feasibility of the proposed strategy is confirmed by results of the simulation directly compared with the experiment, showing in good accordance with the theoretic analysis.
A closed loop speed control for an induction generator is presented. The system was developed for a space vector modulation-voltage source inverter and the three-phase squirrel-cage induction generator to regulate speed and generator voltages with scalar control technique. The aim of this research was to a generated voltage with a constant speed at variable mechanical torque of prime mover. The simulation results show a good performance of the system can be achieved by the proposed speed controller
This paper presents a PWM technique for an asymmetrical dual inverter with a floating capacitor bridge fed an open-end ac load. This technique is to prevent the inrush current during charging into the floating capacitor by using buck-mode operation and to regulate the dc-link voltage its capacitor employing the space-vector PWM strategy for the dual inverter. This is desirable as it leads to avoiding the overcharging of the floating capacitor. These methods help in generating the 13-level voltage waveform of each phase at the output terminal of open-end ac loads in the full range of the modulation index from 0 to 1. Simulation results are illustrated and discussed to validate the effectiveness of the proposed method, which are compared with the existing dual inverters under the same PWM technique in terms of the total harmonic distortion of output phase voltages and so on.
9 September 2019 in ECTI Transactions on Electrical Engineering, Electronics, and Communications
Based on Venturini method, it is in favor of the modulation technique for controlling the matrix converter due to only use of the comparison between the duty cycles in time domain and the triangular carrier wave for generating the gating signals and the achievable voltage ratio between fundamental output magnitude and fundamental input magnitude to 0.866. However, even with simple modulation method and achieving maximum fundamental output magnitude, the possible input voltage unbalance conditions accordingly influence on the output performances (more reduction and distortion). Thus, a control strategy based on Venturini method is presented in this paper, in order to solve the impacts of unbalanced input voltage conditions on the matrix converter performances. Conceptually, this strategy is done by modifying the mathematical model for controlling the modulating waves to satisfy the desirable feature, as generated in the event of normal situation. Up to this approach, it can support either single-phase condition or two-phase condition. Performance of the proposed control strategy was verified by the simplified simulation model in the MATLAB/Simulink software. It is clearly shown that the matrix converter can be controlled for regulating the balanced output voltages with showing good steady-state and dynamic operations without the energy storage devices.
17 September 2025 in IEEE Transactions on Industrial Electronics
This article proposes a circuit analysis and design for an integrated-stage light-emitting diode (LED) driver that uses a Class-E current-driven rectifier and is connected to a Class-D LLC converter. The power switches and a dc-bus capacitor are shared. The proposed LED driver can be divided into a two-stage: the power factor correction (PFC) stage uses the output characteristics of a zero-voltage and zero-derivative-switching (ZVDS) Class-E current-driven rectifier as a power-factor corrector; in addition, this PFC stage is designed for the continuous conduction mode (CCM) operation, and the driver stage uses a zero-voltage switching Class-D LLC converter to supply a constant dc-driven current to the LED load. The circuit operation and step-by-step design of the converter are fully described. The proposed scheme works better with the CCM-ZVDS Class-E current-driven rectifier because it reduces the high current stress on the power switch caused by high di/dt. It also gets rid of the need for a differential mode input filter, and a simple non-isolated matching network without a high-frequency transformer can be used. Finally, a 150-W LED street lighting laboratory prototype is implemented, and experimental results are presented to verify the theoretical analyses of the proposed the integrated-stage LED driver.