The object of research is the processes of occurrence, perception and redistribution of loads in the design of the car brake cylinder in operation. To compensate for angular shifts of the brake cylinder rod at its maximum exit from the housing, improvement measures are proposed. This improvement consists in the use of a safety element to limit the angular movements of the rod when leaving the body. The load of the brake cylinder rod during its angular displacements is determined. The condition for ensuring the strength of the rod is obtained. The optimal parameters of the pipe of the safety element (limiter) of the brake cylinder rod were determined by its allowable moment of resistance. For the possibility of moving the levers interacting with the stem, special windows are provided in the limiter. It is proposed to fix the limiter to the cover by welding. To determine the strength of the brake cylinder, a calculation was made using the finite element method. The results of a robust calculation showed that the maximum equivalent stresses occur in the brake cylinder cover and amount to 118.5 MPa. Therefore, the strength of the brake cylinder is ensured. A feature of the obtained results is that the proposed improvement can be applied not only at the stage of designing a brake cylinder, but also at the stage of modernization. The sphere of practical use of the obtained results is railway transport. The conditions for the practical use of the results are the absence of deformations of the brake cylinder rod. The research carried out will help to improve the efficiency of rolling stock brakes, ensure traffic safety, increase rolling stock speeds, deliver goods, etc. Also, the conducted research will contribute to the creation of developments to improve the reliability of the rolling stock brakes
The object of the research is the processes of thermal stress, perception and redistribution of loads by the brake composite pad during braking of the car in operation. In the current conditions, wedge-dual wear of composite brake pads is observed in the braking systems of freight cars, the feature of which is the deterioration of the braking efficiency of freight trains. With this type of wear, both an increase in the load on the brake pad and an "underuse" of the amount of pressure on it can occur. A comprehensive thermal calculation was carried out for composite brake pads with uniform and wedge-dual wear. The results of the calculation showed that the amount of pressure on an abnormally worn pad is 23.3 % less than that acting on a pad with nominal values. It has been proven that the change in the pressure force on the composite pad with different values of the wear parameters during braking leads to a change in the braking force that occurs between the wheel and the rail during braking. The calculation of the strength of the composite brake pad with wedge-dual wear was carried out. The obtained results will make it possible to develop measures to modernize the elements of the brake lever transmission of freight cars. The field of practical use of the obtained results is car-building enterprises. The conditions for the practical use of the results are the brake lever transmissions of carriages of cars with a gauge of 1520 mm. The conducted studies prove the negative impact of wedge-dual wear not only on braking efficiency, but also on the strength of brake pads. This makes it necessary to create measures aimed at its elimination, which will contribute to increasing the level of train traffic safety and significantly reducing the operational costs of maintaining freight cars
26 February 2021 in Eastern-European Journal of Enterprise Technologies
An analysis of the method for ensuring the sinusoidality of the output voltage in power generation systems with self-commutated voltage inverters under the requirements of the international standard IEEE-519 is presented. In a number of programs, especially low-power generation systems, a low-cost solution is needed to provide the sinusoidal waveform of the output voltage with the total harmonic distortion of 5 %. This solution is to use two-level voltage inverters with an output sine LC filter. However, the feature of the sine filter with the frequency converter is that the PWM frequency affects the spectrum of higher harmonics of the output voltage. In addition, there is the starting current of the filter capacitor, which can disable the power switches of the voltage inverter. The developed method for calculating the values of the LC filter with the two-level voltage inverter in the PWM mode is presented meeting the requirements of the international standard IEEE-519, taking into account the modulation frequency and limitation of the starting current of the filter capacitor. To confirm the required quality of the output voltage of the two-level voltage inverter with the sine filter, an appropriate simulation model was created in the Matlab/Simulink computer simulation environment. The oscillograms and harmonic analysis of the input and output voltages of the sine filter, which showed the total harmonic distortion of 1.88 %, are presented. A physical prototype of the investigated system was created on the basis of a 5.5 kW OVEN PChV203-5K5-V frequency converter (Ukraine). Using the SIGLENT SDS1104X-E oscilloscope (China), the real waveform and the results of the harmonic analysis of the sine filter output voltage, confirming the implementation of the necessary sinusoidality criteria, were obtained
This article presents the results of a study focused on identifying the main causes of the asymmetric (clinodual) wear of composite brake pads on freight wagons. A new scientific approach to determining the clinodual wear of composite brake pads on freight wagons is proposed. It is established that the harmful abrasion of the pad occurs during the movement of the freight train due to an imperfection in the bogie-brake lever transmission. The causes of the non-normative frictional wear of composite brake pads were investigated. This kind of wear leads to the tilting and abutting of the upper end of the brake pads against the rotating wheel during train running. The results of geometric and kinetostatic studies of the “pad–wheel” tribotechnical pair are provided to establish the causes and consequences of the accelerated clinodual frictional wear of composite brake pads on pendulum suspension in the bogies of freight wagons. The conditions of rotation of the wheels during braking “for” and “against” the clockwise direction depending on the direction of the train are considered. A new approach to brake-pad-wear prediction depending on the mileage of wagons under operational conditions is proposed. The research conducted in this study contributes to the development of the mechanical parts of freight-wagon brakes, increasing the efficiency of brake operation and improving the safety of train traffic.
8 January 2024 in Communications - Scientific letters of the University of Zilina
The work highlights the results of a study into the dual wedge-shaped wear of composite brake pads for freight wagons. It has been found that the over-normative wear makes the area of a composite brake pad larger in the lower part up to a valu...
The complex of operational studies and theoretical research was performed on the occurrence of harmful wear that changes geometrical parameters of the useful contact area of the brake pads of freight cars at various established standard clearance between the pad and the wheel, which significantly impairs the braking efficiency of trains. The inspections of the mechanical part of the brakes attracted attention to the abnormal wear of the brake pads of the freight cars, which occurs because the common centre of gravity of the pad and the brake shoe, which are on the pendular suspension, do not coincide with the centre of the hole in the brake strut for any pad. The results of calculations using the coordinate method performed in the Mathcad software environment and the graphical one performed in AutoCAD to determine the geometrical parameters of the formation of the upper harmful wear of the pad depending on the standard clearance between the wheel and the brake pad were compared to proved theoretically that the error between them does not exceed 5-7%.