To study the effect of Ce on the morphology of manganese sulfide, we added different contents of Ce into U75V heavy rail steel. The composition and morphology of sulfide in steel were analyzed. The inclusions’ number, size, and aspect ratio were analyzed by automatic scanning electron microscope ASPEX. The results show that the inclusions in heavy rail steel without Ce are elongated MnS and irregular Al-Si-Ca-O inclusions. With the increase of Ce from 52 ppm to 340 ppm, the composition of main inclusions changes along the route of Ce2O2S-MnS → Ce2O2S-MnS-Ce2S3 → Ce2O2S-Ce3S4-Ce2S3 → Ce2O2S-Ce3S4-CeS. Ce has a noticeable spheroidization effect on MnS, which can make inclusions finely dispersed. When Ce content is 139 ppm, the average size of inclusions is the smallest. The mechanism of Ce-modified MnS was discussed by combining experimental results with thermodynamic calculations. Finally, the effect of Ce treatment on inhibiting MnS deformation was verified by simulated rolling.
1 April 2016 in Journal of Iron and Steel Research International
Vacuum smelting experiments were conducted to investigate the effects of different initial nitrogen content and surface active elements on nitrogen denitrification and nitrogen absorption in molten steel. Thermodynamic calculations show that the pressure corresponding to 10 ppm of [N] should be less than 45 Pa; at 30 Pa and 1600°C, the nitrogen content in the steel reduced from 18 to 10 ppm in 50 min. Furthermore, denitrification can be described as a 1.5th order reaction model. In addition, the mean parameters of nitrogen absorption between the ultra-low and common-nitrogen steels are different: for ultra-low nitrogen molten steel exposed to air, even if [S] ≥ 200 ppm and [O] ≥ 300 ppm, [N] can increase from 10 to over 40 ppm in 20 min.
28 February 2019 in Metallurgical Research & Technology
The source and generated mechanisms of DS-size inclusions in bearing steel were studied by sampling systematically and using ASPEX, SEM and EDS to analyse the morphology, composition and amount of non-metallic inclusions larger than 13 µm. Two kinds of typical DS-size inclusions were found in the refining process: type I is CaO-MgO-Al2O3-SiO2 distributed evenly and wrapped by CaS; type II is composite inclusion with MgO-Al2O3 as the core, CaO-Al2O3 and CaO-SiO2 as the inner layer, covered by CaS. Based on the FactSage and thermodynamic calculations, the DS inclusions formation mechanisms were drawn. There are two formation mechanisms of the type II inclusions: one is the solid phases will precipitate from the matrix of type I inclusions as the temperature drops; another is that when the reaction time is not sufficient, the MgO∙Al2O3 spinel core will not be transformed completely, and the evolution can be summarized as: Al2O3 → MgO-Al2O3 → CaO-MgO-Al2O3 → surrounded by CaO-Al2O3(SiO2) → covered by CaS.
Polar steel requires good strength and excellent toughness for breaking icy surfaces in low-temperature sea water environments. In this study, the effect of inclusions and metallurgical structure on the mechanical property of polar steel was examined. The composition and morphology of the inclusions in steel were formed using different deoxidation methods during steel refining, and steel plates were rolled by the same rolling process. The results show that there are lower inclusion densities and more globular inclusions in steel deoxidized using Zr–Ti than deoxidized using Al. The mean diameters of grains in Zr–Ti-killed steel from different thicknesses are smaller than that in Al-killed steel, the impact toughness and yield strength of Zr–Ti-killed steel are substantially higher than those of Al-killed steel. It is determined that the use of the Zr–Ti deoxidizer has a positive effect on the ductility of the steel.