Titanium alloys are difficult to machine using conventional methods, therefore, nonconventional processes are often chosen in many applications. Electrical discharge machining (EDM) is one of those nonconventional processes that is used frequently for shaping titanium alloys with their respective pros and cons. However, a good understanding of this process is very difficult to achieve as research results are not properly connected and presented. Therefore, this study investigates different types of EDM processes such as, wire EDM, die-sink EDM, EDM drill and hybrid EDM used to machine titanium alloys. Machining mechanism, tool electrode, dielectric, materials removal rate (MRR), and surface integrity of all these processes are critically analysed and correlated based on the evidence accessible in literature. Machining process suffer from lower material removal rate and high tool wear while applied on titanium alloys. Formation of recast layer, heat affected zone and tool wear is common in all types of EDM processes. Additional challenge in wire EDM of titanium alloys is wire breakage under severe machining conditions. The formation of TiC and TiO2 are noticed in recast layer depending on the type of dielectrics. Removal of debris from small holes during EDM drilling is a challenge. All these restricts the applications EDMed titanium alloys in high-tech applications such as, aerospace and biomedical areas. Most of these challenges come up due to extraordinary properties such as, low thermal conductivity, high melting point and high hardness, of titanium alloys. Though hybrid EDM has been introduced and there is some work on simulation of EDM process, further developments in EDM of this alloy is required for widening the application of this methods.
This paper presents a review on the modeling of ablation and plasma expansion processes in the pulsed laser deposition of metals. The ablation of a target is the key process that determines the amount of material to be deposited; while, the plasma expansion governs the characteristics of the deposited material. The modeling of ablation process involves a study of two complex phenomena: (i) laser-target interaction and (ii) plasma formation and subsequent shielding of the incoming radiation. The laser-target interaction is a function of pulse duration, which is captured by various models that are described in this paper. The plasma produced as a result of laser–target interaction, further interacts with the incoming radiation, causing the shielding of the target. The shielding process has been modeled by considering the various photon absorption mechanisms operative inside the plasma, namely: inverse Bremsstrahlung, photoionization, and Mie absorption. Concurrently, the plasma expands freely until the ablated material gets deposited on the substrate. Various models describing the plasma expansion process have been presented. The ability of the theoretical models in predicting various ablation and plasma characteristics has also been compared with the relevant experimental data from the literature. The paper concludes with identification of critical issues and recommendations for future modeling endeavors.
23 May 2019 in Journal of Micromechanics and Microengineering
Microchannels formed in non-conductive substrates like fused silica, glass and quartz, etc, have wide applications in the field of micro-fluidic and lab-on-chip applications due to their optical transparency, chemical inertness, and biocompatible nature. Electrochemical discharge machining (ECDM) has emerged as a potential low-cost fabrication method to fabricate microfeatures in these materials, compared to conventional laser etching techniques. In this paper, numerical simulation and experimental fabrication of microchannels in a glass substrate using the ECDM based micromilling technique is demonstrated. Stainless steel needle as tool electrode is used in alkaline electrolyte medium. The effects of process parameters viz. tool feed rate, pulse frequency and machining voltage on material removal rate (MRR) and surface roughness (SR) of the microchannels were analysed. The experimental results showed that the MRR and SR increases with an increase in machining voltage and tool feed rate but reduces with an increase in the pulse frequency. Simulations using FEM-based model showed similar trends in MRR with that of experiments. A comparison between the cross-section profiles obtained by the experimental work and predicted profile by the numerical simulation showed some deviation between them due to the Gaussian heat flux assumption in the numerical model. Optical images showed that KOH performance is comparatively better than NaOH with respect to thermal damage and width of cut. Further, multi-objective optimization was performed using utility theory coupled with Taguchi’s method to optimize the process parameters. Moreover, the capability of the ECDM process was demonstrated in fabricating various other micro-features such as sinusoidal channel, letter engraving, etc in a glass substrate, which can be extended to other brittle materials like quartz, fused silica, ceramic, etc.
19 February 2014 in Journal of Physics D: Applied Physics