A guidance and control strategy for a class of 2D trajectory correction fuze with fixed canards is developed in this paper. Firstly, correction control mechanism is researched through studying the deviation motion, the key point of which is the dynamic equilibrium angle. Phase lag of swerve response is the dominating factor for correction control, and formula is deduced with the Mach number as argument. Secondly, impact point deviation prediction based on perturbation theory is proposed, and the numerical solution and application method are introduced. Finally, guidance and control strategy is developed, and simulations to validate the strategy are conducted.
18 May 2021 in International Journal of Aerospace Engineering
A novel H∞ filter called square-root cubature H∞ Kalman filter is proposed for attitude measurement of high-spinning aircraft. In this method, a combined measurement model of three-axis geomagnetic sensor and gyroscope is used, and the Euler angle algorithm model is used to reduce the state dimension and linearize the state equation, which can reduce the amount of calculation. Simultaneously, the method can be applied to the case of measurement noise uncertainty. By continuously modifying the error limiting parameters to update the measurement noise estimation, the filtering accuracy and robustness can be improved. The square-root forms enjoy a consistently improved numerical stability because all the resulting covariance matrices by QR decomposition are guaranteed to stay positive semidefinite. The algorithm is applied to the simulation experiment of attitude measurement with the combination of geomagnetic sensor and gyroscope and compared with the results of Unscented Kalman filter, cubature Kalman filter, square root cubature Kalman filter, and singular value decomposition cubature Kalman filter, which proves the effectiveness and superiority of the algorithm.
1 October 2019 in IOP Conference Series: Materials Science and Engineering
Missile Datcom (hereinafter referred to as Datcom) is an aerodynamic engineering calculation software developed by the US Air Force Research Laboratory. It is commonly used in the preliminary design of the shape scheme of missiles, aircraft and other aircraft. In this paper, Datcom is used to calculate the aerodynamic parameters of a two-dimensional ballistic correction projectile(D2BCP), and the calculated data is compared with the wind tunnel test data. The analysis results show that Datcom calculates the axial force coefficient (CA) of the projectile with large system deviation, however, the deviation can be eliminated by a certain compensation, thereby obtaining a more accurate CA of the projectile. Datcom calculates the normal force coefficient (CN) with high Mach number accuracy, but there is an unacceptable deviation of the projectile CN calculated at small angle of attack ( α ). The calculation of pitching moment coefficient with α (CMa) is higher, but the error is larger under individual Mach numbers.
Aiming at the increasing demand for fine and efficient detection of underwater magnetic field in the field of marine exploration, especially in the military field, a modular data acquisition scheme integrating magnetic sensors and underwater positioning sensors is proposed, and an underwater multi-parameter data acquisition system based on NI CompactRIO is constructed. The system integrates two cesium optically pumped magnetometers, fluxgate magnetometers, and underwater integrated navigation and positioning modules to meet the experimental requirements under different conditions. In order to solve the problem of data synchronization when multiple sensors are collected at the same time, a synchronization scheme based on the external Oven Controlled Crystal Oscillator reference signal source is proposed. While ensuring data synchronization in the underwater environment where PPS signals cannot be received, the influence of ambient temperature changes on synchronization is further reduced. The output signal measurement module of dual-channel cesium optically pumped magnetometer is realized by using the improved direct frequency measurement method. This method improves the frequency measurement accuracy on the basis of ensuring multi-channel consistency. The acquisition system is based on the modular design concept, which can efficiently complete the acquisition task, and is easy to integrate and has high application value.
1 October 2019 in IOP Conference Series: Materials Science and Engineering
As a new type of ammunition, the trajectory correction projectile has much different ballistic characteristics than traditional uncontrolled ammunition and missile. The firing precision of trajectory correction projectile is significantly higher than that of uncontrolled projectile and lower than missile. Also the evaluation method for firing precision is different from that of uncontrolled projectile and missile. In this paper, by analyzing the calculation methods and characteristics of different firing precision evaluation indicators, the method suitable for evaluating the precision of trajectory correction projectile is determined, which provides theoretical and technical support for acceptance of trajectory correction projectile firing precision.
When a high-speed rotating projectile faces high impact loads, the sensitive parts of the control system can get damaged, resulting in operational failure. It is crucial to develop a unique buffer structure that offers impact resistance and has a small contact area. An annularly distributed multi-sphere point contact structure was designed and fabricated on a magnesium alloy substrate based on the Hertz contact theory. The accuracy of the finite element numerical model, constructed using Abaqus/Explicit, was verified through hydraulic impact tests. The impact mechanical properties of the structure were studied by analyzing the influence of the number, diameter, and cavity radius of hemispheres using an experimentally verified finite element model. The axial and radial deformations of the structure were compared and analyzed. The research findings indicate that the deformation and impact resistance of the structure can be greatly influenced by increasing the number of hemispheres, enlarging the hemisphere diameter, and incorporating internal cavities. Specifically, with 6 hemispheres, each with a diameter of Φ 6 mm and a cavity radius of R1.5 mm, the axial and radial deformations are only 1.03 mm and 3.02 mm, respectively. The contact area of a single hemisphere is 7.16 mm2. The study offers new perspectives on choosing buffer structures in high-impact environments.