Andre Desbiens

Prof. Andre Desbiens

orcid

Research Focus & Metrics

Academic Career Length

31Years (1996-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 January 1996 in IEE Proceedings - Control Theory and Applications
Verified
Journal Article
Closed access
ADAndre Desbiens
Andre Desbiens
APA. Pomerleau
A. Pomerleau
DHD. Hodouin
D. Hodouin
A systematic tuning method of SISO controllers for two-by-two processes is proposed. The first step consists of selecting, for each loop, the desired tracking closed-loop dynamics. From this information, the open-loop characteristics are deduced, leading to the frequency responses (magnitude and phase) of the unknown SISO controllers. An optimisation method is used to get a good approximation of each corresponding transfer function. Constraints are implemented to ensure a stable closed-loop system. For processes having delays, a Smith predictor structure is proposed. This frequency based tuning method is tested on three different processes (minimum and nonminimum phase) and leads to performances corresponding closely to the closed-loop specifications.

14 June 2009
Verified
Conference Paper
Closed access
PBPierre-Richard Bilodeau
Pierre-Richard Bilodeau
ÉPÉric Poulin
Éric Poulin
EGEric Gagnon
Eric Gagnon
FWFranklin Wong
Franklin Wong
ADAndre Desbiens
Andre Desbiens

1 January 2011 in Journal of Guidance, Control, and Dynamics
Verified
Journal Article
Closed access
CPCarole G. Prévost
Carole G. Prévost
ADAndre Desbiens
Andre Desbiens
ÉGÉric Gagnon
Éric Gagnon
DHDaniel Hodouin
Daniel Hodouin

19 June 2005
Verified
Conference Paper
Closed access
MMMyriam Manaï
Myriam Manaï
ADAndre Desbiens
Andre Desbiens
ÉGÉric Gagnon
Éric Gagnon

1 June 2010
Verified
Conference Paper
Closed access
VMVincent Myrand-Lapierre
Vincent Myrand-Lapierre
ADAndre Desbiens
Andre Desbiens
EGEric Gagnon
Eric Gagnon
FWFrank Wong
Frank Wong
EPEric Poulin
Eric Poulin
This article describes a control strategy to bridge the autonomous transition between level and hovering flight of a fixed-wing mini-aerial vehicle. These autonomous transitions, combined with the level-flight and hovering modes, would permit dangerous missions like reconnaissance in hostile or restricted areas. Then, there are four flight modes during a mission : the level-flight, the level-flight to hovering (L2H), the hovering, and the hovering to level-flight (H2L). The model structures for both level-flight and hovering modes are based on the linearization of a six-degree-of-freedom rigid body model of a fixed-wing mini-aerial vehicle. Controllers for both main flying modes are presented. The L2H mode is managed by the level-flight controller, whereas the H2L is managed by the hovering controller. A systematic approach based on a logic-based switching supervisor is developed to manage the transition between modes. Experimental results of a mini-aerial vehicle testbed which uses the switching supervisor are presented.

17 August 2021 in Advanced Powder Technology
Verified
Journal Article
Open access
ATAlex Thivierge
Alex Thivierge
JBJocelyn Bouchard
Jocelyn Bouchard
ADAndre Desbiens
Andre Desbiens
Modelling the high-pressure grinding rolls mass flow rate from the continuity principle represents a difficult task, partly because the ore may slip against the rolls. In effort to increase the understanding of this phenomenon, this paper introduces a state observer to estimate the slip profile in the HPGR working gap from the force balance equations and Coulomb friction criterion. The observer is used off-line and a posteriori, i.e. it requires a series of HPGR tests conducted at different levels of specific force and roll speed. It allows observing the slip profile on a gold ore at the pilot scale. As the material enters the compression zone, it descends at a slower rate than the vertical component of the roll peripheral speed. As it progresses downward, its velocity increases. It exceeds the roll peripheral speed at the working gap level and peaks below. The pressure peaking above the working gap makes slipping possible. It leads to the material above the working gap to push onto the one below and thus accelerating it.