Introduction: Cemento-ossifying fibromas are rare, benign lesions of the head and neck regions. The origin of these lesions can be traced to the periodontal ligament, because its cells are able to form cement, lamellar bone, or fibrous tissue. Case presentation: A rare case report of a young Caucasian female with a COF is described including follow-ups. She remained untreated for several years despite early radiographic findings of the lesion without a definitive diagnosis. The patient ultimately underwent radical surgery and the whole lesion was removed. The subsequent histological examination confirmed the clinical diagnosis of a COF. Since then, the patient has been under regular clinical and radiological follow-ups. Discussion: This rare case report of a COF, documented over 18 years, shows the importance of consecutive therapy after radiologic and clinical findings, as such lesions continue growing and may subsequently lead to severe medical conditions. Therefore, complete surgical resection of COFs is advised to achieve good results in terms of health and recurrence. Conclusion: Long-term follow-up of patients is required as recurrences can occur for up to 10 years following treatment. Well-planned radical and wide surgical resection of these lesions has proven not only to be effective in eliminating the aetiological factors, but can also achieve decent bone regeneration and aesthetic results with almost no deformation in the surgical site. Highlights:

Bone and soft-tissue calcifications are often coincidentally diagnosed on digital panoramic radiographs (DPRs). As the use of three-dimensional (3D) images has increased in the past decade for diagnostics in the mandibular region, we evaluated 3D volume images derived from 2D panoramic images to determine if this method is suitable for early detection of calcifications in this region. In this study, three investigators retrospectively and independently evaluated 822 DPRs. If one or more calcifications were present, the 3D volume image from that patient was retrospectively evaluated to confirm the incidental findings. A radiographic system with a low-dose mode and a high-resolution 3D-image function was used. The investigators focussed on the most common calcifications, including tonsilloliths (TL), idiopathic osteosclerosis (IO) of the mandible, carotid artery calcifications (CAC), calcified submandibular lymph nodes (hereafter, CSL), and sialoliths of the submandibular salivary gland (SSG). One or more calcifications were identified in 415 (50.5%) DPRs. In total, 718 calcifications were detected, 30.2% of which were TL, 16.3% IO, 11.3% CAC, 8.8% CSL, and 1.7% SSG. Only 287 (39.97 %) of the calcifications were confirmed on 3D volume images; of these, 29.2% were TL, 58.5% IO, 0.2% CAC, and 1.4% SSG. No CSLs were detected. Not all areas shown on the DPRs were visible in the retrospectively obtained 3D volume images. Whereas DPRs are used to diagnose calcifications such as IO, TL, SSG, CAC, and CSL, the 3D volume images were only useful for confirming the existence of IO, TL, and SSG calcifications.

Background: In terms of a highly atrophic maxilla, bone augmentation still remains very challenging. With the introduction of computer-aided design/computer-aided manufacturing (CAD/CAM) for allogeneic bone blocks, a new method for the treatment of bone deficiencies was created. This case report demonstrates the successful use of two specially designed and CAD/CAM manufactured allogeneic bone blocks for a full arch reconstruction of a highly atrophic maxilla with an all-on-six concept. Case presentation: We report the case of a 55-year-old male patient with a highly atrophic maxilla and severe bone volume deficiencies in horizontal and vertical lines. In order to treat the defects, the surgeon decided to use a combination of two allogeneic bone blocks and two sinus floor augmentations. The bone blocks were fabricated from the data of a cone beam computed tomography (CBCT) using CAD/CAM technology. After the insertion of the two bone blocks and a healing period of 7 months, six dental implants were placed in terms of an all-on-six concept. The loading of the implants took place after an additional healing time of 7 months with a screw-retained prosthetic construction and with a milled titanium framework with acrylic veneers. Conclusion: The presented procedure shows the importance of the precise design of CAD/CAM manufactured allogeneic bone blocks for the successful treatment of a highly atrophic maxilla. Proper soft-tissue management is one of the key factors to apply this method successfully.

Introduction: Dental implants present an advanced technique for the rehabilitation of partial or edentulous patients. Tooth loss caused by caries, periodontal disease or systemic factors often results in a decline of the bucco-lingual alveolar ridge dimension. Within one year the initial bone width can be resorbed up to 50%. As a consequence dental implants may be limited for rehabilitation and cannot be performed in a conventional manner because of the risk of dehiscence and fenestrations. Bone blocks, guided bone regeneration (GBR), horizontal osteogenic distraction and bone grafts may be used for augmentation procedures. In case of sufficient vertical bone dimension, an alveolar ridge splitting and augmentation technique (ARST) can be conducted. This case has been reported in line with PROCESS criteria [1]. Case presentation: We present a 51-year old female patient, who has had a full denture for about 30 years. The reason for consultation was the demand for a fixed prosthesis. Dental implants in combination of the ARST with GBR allowed us to correct horizontal deformities of the alveolar ridge. Discussion: We discuss the possibility of using the ARST in the interantral region for a full arch rehabilitation of the maxilla with simultaneous dental implant placement in a narrow alveolar ridge. Conclusion: The ARST in addition to simultaneous implant placement with a GBR can be successfully used for a full arch rehabilitation of the maxilla in a narrow alveolar ridge.