Urban planning is considered one of the most important research spaces currently in existence, as it directly affects the daily life. Building Information Modelling (BIM) and Geographic information system (GIS) became a powerful platform because of their variety individual features and capabilities. But each platform contains weaknesses. In order to overcome these weaknesses, the integration of BIM and GIS must be obtained. So this paper aims to review recent studies that are based on the integration between GIS and BIM technologies in the field of urban planning. Finally, and through what has been reviewed from the studies, the summary showed that the importance of these technologies lies in the many types of their uses in the field of urban planning such as strategic urban planning, site selection, land use, master planning and future planning.
19 August 2021 in International Journal of Construction Management
The energy sector is always facing huge challenges specially in countries with highly inflated population where the building sector has more pressure to reduce energy consumption. To achieve more energy efficiency in residential buildings with lower life cycle cost (LCC) and enhanced thermal comfort conditions, this study develops a multi-objective genetic algorithm model for the three major climates in Egypt (Mediterranean, semi-arid and arid). The design variables considered include external wall type, roof type, window to wall ratio (WWR), building orientation, HVAC system setpoint and HVAC operation schedule. Available sustainable materials in Egypt are considered for building envelope alternatives, such as limestone and polyurethane expanded. The main findings from the study approved that the optimum solutions in all climates have successfully balanced the reduction in energy consumption and LCC. However, the discomfort hours in both Mediterranean and Semi-arid climates have less reduction percentages compared to the arid climate.
10 May 2024 in Innovative Infrastructure Solutions
Few researchers have investigated the internal torsional reinforcement of box beams, So, this study aims to find out the possibility of adding a certain percentage of RCA to the NC mixtures, as well as verifying the success achieved in repairing the cracks that occurred as a result of torsion with CFRP or injecting with epoxy, which has not been addressed in previous research and literature reviews. This study reinforces reinforced SCC box columns subjected to complete torsion with CFRP sheets and epoxy resin injections. Four types SCC specimens (the first beam with 0%, the second beams with 33.3%, the third beams with 67.7%, and the fourth beams with 100% RCA by weight) were subjected to pure torsion until failure. The dimensions and reinforcement of every specimen are identical. In addition, the applied torque-twist angle relationship at the midspan and end span was investigated. Bending experiments were performed to establish load-deflection curves and assess failure modes. After structural rehabilitation, all beams exhibited increased rigidity values, according to the results. Epoxy resin and CFRP sheet contributed to the specimens' increased ultimate load. The ultimate strength of RCA beams strengthened with CFRP and injected with epoxy increased. The specimens' flexural strength was considerably enhanced by the combination of surface roughness and fracture injection, and the effectiveness of using RCA was very good; it could be replaced with NCA in concrete mixtures, according to the ratio and need. Doi: 10.28991/CEJ-2023-09-11-05 Full Text: PDF
30 March 2023 in Al-Qadisiyah Journal for Engineering Sciences
Reinforced concrete (RC) elements lose their structural strength by exposing to fire as the mechanical properties of the reinforcing steel and concrete deteriorate due to the heat. This study provides an understanding of the behavior of three structural concrete elements: beam, column, and slab at high temperatures using a finite element (FE) modelling produced in ABAQUS, as well as the potential of retrofitting of these elements using Slurry Infiltrated Fiber Concrete (SIFCON). The use of SIFCON has shown excellent results compared to the fire damaged elements, and to the undamaged concrete elements in term of various indices (ultimate load capacity, stiffness, toughness and ductility).
One of the most significant building materials used to build a variety of infrastructure, military, and civil structures is concrete. It can effectively withstand fire mishaps for a long period of time. This study employs a finite element simulation approach in Three steps: the first involves applying mechanical loading, the second involves applying mechanical and thermal loading; and the third involves strengthening the damaged model. Two different strengthening procedures were used to evaluate the performance of the fire-damaged slab. Two types of strengthening techniques—carbon-fiber-reinforced polymer (CFRP) sheet and slurry-infiltrated fibrous concrete (SIFCON) jacketing—were used. Studying the performance of SIFCON and CFRP together and in two different thicknesses of each for repairing both normal and high-strength concretes after fire exposure is considered limited. An investigation of their behavior can provide insights into how effective the restoration of strength is. The study aims to assess how well various repair materials perform in restoring the durability and strength of reinforced concrete members after being exposed to fire. This will assist in determining the best materials for concrete repair after a fire. Results show that the enhancements by SIFCON with a thickness of 30 mm significantly improved many indices, including load displacement behavior, ductility, and absorption energy of the slab. Doi: 10.28991/CEJ-2023-09-08-013 Full Text: PDF