Typical parallel fractures are often observed in the outcrops of inclusions in the field. To reveal the failure mechanism of inclusions embedded in rock matrix, a series of heterogeneous models are established and tested based on the damage mechanics, statistical strength theory, and continuum mechanics. The results show that, with the spacing between two adjacent fractures decreasing, the stress is firstly transferred from negative to positive, then from positive to negative. Stress transition is profound for the fracture spacing. Meanwhile, three types of fractures, i.e., consecutive fracture, non-consecutive fracture, and debonding fracture, are found, which are consistent with the observed modes in the field. Multiple inclusions are often fractured easier than an isolated inclusion due to the stress disturbance between inclusions and newly generated fractures. Either in single or multiple inclusions, tensile stresses inside the inclusions are the main driving force for fracture initiation and propagation. Besides, although the material heterogeneity has a small effect on the stress variation, it has an evident impact on the fracturing mode of inclusions. The stiffness ratio is critical for the stress transition and failure pattern; the interface debonding occurs earlier than the fracture initiation inside the inclusion when the stiffness ratio is relatively high. Additionally, the inclusions content only affects the sequence of fracture initiation rather than the final fracture spacing pattern.

The purpose of this study is to study the damage and fracturing effects of high-voltage discharge on coal-rock mass under the action of hydrostatic pressure. Based on the traditional damage evolution model and the change of the effective bearing area and stress around the microcrack of coal-rock mass on a microscopic scale, the expression of macroscopic damage variation of coal-rock mass under the action of electrohydraulic coupling was derived, and its damage constitutive relation was established. The high-voltage pulse water shock stress test of coal-rock mass under the conditions of different water pressures and voltages was carried out, and its damage numerical model was established by the ABAQUS/XFEM. The damage variable values of coal-rock mass with different electrohydraulic parameters were compared to characterize the generation and expansion of internal macroscopic cracks. From the results, it is shown that the damage variable based on the effective bearing area and stress around the crack can represent the morphology and expansion change of crack of coal-rock mass with different electrohydraulic parameters clearly and quantitatively. Different hydrostatic pressures and discharge voltages have influence on the damage variables of coal-rock mass, but different influencing degrees cause different damages on coal-rock mass. The damage of coal rock can be characterized by the change of the effective bearing area and stress around microcracks in coal body. So, stress testing and numerical simulation have verified the correctness of the damage model.

In order to investigate freeze–thawed red sandstone failure processes under cyclic loading and unloading conditions, real-time acoustic emission (AE) and scanning electron microscopy (SEM) techniques were used to reveal the fracture process of the saturated red sandstone after cyclic loading and unloading tests using uniaxial compression. The results show that the stress–strain curves of the freeze–thawed sandstones show signs of hysteresis and exhibit a two-stage evolution of “sparse → dense”. In the cyclic loading and unloading process, the modulus of elasticity in the loading process is always larger than that in the unloading process, while the Poisson’s ratio is the opposite, and the radial irreversible strain and cumulative irreversible strain are larger than those in the axial direction. As the number of freeze–thaw cycles increases, the rock specimens need more cycles of loading and unloading to make the crack volume compressive strain $\Delta {\epsilon }_{cv}^{+}$ reach the maximum value and tend to stabilize, while the crack volume extensional strain $\Delta {\epsilon }_{cv}^{-}$ tends to decrease gradually. This study also shows that the growth phase of the cyclic loading and unloading process has more ringing counts and a shorter duration, while the slow degradation phase has more ringing counts with loading and less with unloading. In addition, the F-T cycle gradually changes the internal microcracks of the red sandstone from shear damage, which is dominated by shear cracks, to tensile damage, which is dominated by tensile cracks. This study’s findings contribute to our knowledge of the mechanical characteristics and sandstone’s degradation process following F-T treatment, and also serve as a guide for engineering stability analyses conducted in the presence of multiphysical field coupling.

With the rapid advancement of urban underground space development, shield tunnel construction has seen a significant increase. However, at the initial launching stage of shield tunnels in shallow-buried weak strata, engineering risks such as face instability and sudden surface settlement frequently occur. At present, there are relatively few studies on the reinforcement technology of the initial section of shield tunnel in shallow soft ground and the evolution law of ground disturbance. This study takes the launching section of the Guanggang New City depot access tunnel on Guangzhou Metro Line 10 as the engineering background. By applying MIDAS/GTS numerical simulation, settlement monitoring, and theoretical analysis, the reinforcement technology at the tunnel face, the spatiotemporal evolution of ground settlement, and the mechanism of soil disturbance transmission during the launching process in muddy soil layer are revealed. The results show that: (1) the reinforcement scheme combining replacement filling, high-pressure jet grouting piles, and soil overburden counterpressure significantly improves surface settlement control. The primary influence zone is concentrated directly above the shield machine and in the forward excavation area. (2) When the shield machine reaches the junction between the reinforced and unreinforced zones, a large settlement area forms, with the maximum ground settlement reaching −26.94 mm. During excavation in the unreinforced zone, ground deformation mainly occurs beneath the rear reinforced section, with subsidence at the crown and uplift at the invert. (3) The transverse settlement trough exhibits a typical Gaussian distribution and the discrepancy between the measured maximum settlement and the numerical and theoretical values is only 3.33% and 1.76%, respectively. (4) The longitudinal settlement follows a trend of initial increase, subsequent decrease, and gradual stabilization, reaching a maximum when the excavation passes directly beneath the monitoring point. The findings can provide theoretical reference and engineering guidance for similar projects.

In modern tunnel construction, complex environments with high geothermal gradients and abundant groundwater are frequently encountered. To investigate the damage and failure mechanisms of sandstone under the combined effects of temperature and water, uniaxial compression tests were conducted on sandstone at different temperatures (25 °C, 55 °C, 85 °C, and 95 °C) and soaking durations (0.5 h, 1 h, and 3 h). The acoustic emission (AE) signals and energy evolution during the damage and failure processes were analyzed, revealing the damage characteristics and failure mechanisms of sandstone. The results indicate the following: (1) As the temperature increases, under the 3 h condition, the water content of sandstone is highest at 55 °C, reaching 3.01%, and the thermal expansion effect of sandstone is not obvious. Under the conditions of 85 °C and 95 °C, the thermal expansion effect leads to a decrease in the water content, enhances the water absorption softening effect, increases the plastic deformation capacity of sandstone, and weakens its brittle failure capacity. (2) When soaked for 0.5 h and 1 h, the maximum acoustic emission ring count and maximum acoustic emission energy of sandstone increase initially, then decrease, and subsequently increase again as the temperature rises, while the cumulative acoustic emission ring count gradually increases with temperature. Under the 3 h soaking condition, the maximum ring count, maximum energy, and cumulative ring count of sandstone at all temperatures show a consistent increasing trend with temperature. (3) The increase in soaking time reduced the damage variable of sandstone, with the largest reduction of 54.17% under the 3 h condition. At different temperatures, the damage variable of sandstone was smallest at 55 °C, only 0.33. (4) Sandstone primarily experiences tensile failure under different temperatures and soaking times. The extension of soaking time promotes the development of shear cracks, while the increase in temperature can effectively promote the expansion of tensile cracks. The research results provide certain theoretical references for the damage and failure of surrounding rock in modern tunnel construction.

To investigate the influence of segmental lining width on ground and tunnel deformation during shield tunneling beneath residential buildings, a numerical analysis model was established using Midas GTS NX based on the engineering context of the Guangzhou Metro Guanggang Xincheng depot tunnel underpassing residential structures. The simulation results were validated through comparison with field monitoring data, and a gray relational analysis was employed to quantitatively assess the sensitivity of various deformation indicators to segment width. The findings indicate that, under the engineering scenario of a shield tunnel crossing beneath residential buildings, the use of 1.2 m-wide segments is more effective in controlling ground settlement and structural deformation of the tunnel compared with 1.5 m-wide segments. The deformation process associated with the 1.2 m segments exhibits a more stable settlement pattern, whereas the 1.5 m segments tend to induce repeated settlement–heave cycles in the surrounding ground, with a potential risk of segmental displacement exceeding warning thresholds. Sensitivity analysis shows that different deformation indicators respond unevenly to changes in segment width. From most to least sensitive, the indicators rank as follows: maximum ground deformation, maximum displacement during the post-excavation stage, and maximum displacement during the excavation stage. The results of this study provide theoretical support and reference for selecting segmental lining width in shield tunnels constructed beneath residential buildings.