Hydrogen has received substantial attention because of its diverse application in the energy sector. Steam methane reforming (SMR) dominates the current hydrogen production and is the least expensive endothermic reaction to produce grey hydrogen. This technology provides the advantages of low cost and high energy efficiency; however, it emits an enormous amount of CO₂. Carbon capture storage (CCS) technology helps reduce these emissions by 47% to 53%, producing blue hydrogen. Methane pyrolysis is an alternative to SMR that produces (ideally) CO₂-free turquoise hydrogen. In practice, methane pyrolysis reduces CO₂ emissions by 71% compared to grey hydrogen and 46% compared to blue hydrogen. While carbon dioxide emissions decrease with CCS, fugitive methane emissions (FMEs) for blue and turquoise hydrogen are higher than those for grey hydrogen because of the increased use of natural gas to power carbon capture. We undertake FMEs of 3.6% of natural gas consumption for individual processes. In this study, we also explore the utilization of biogas as a feedstock and additional Boudouard reactions for efficient utilization of solid carbon from methane pyrolysis and carbon dioxide from biogas. The present study focuses on possible ways to reduce overall emissions from turquoise hydrogen to provide solutions for a sustainable low-CO₂ energy source.

Effect of fines content (weight % of particles with diameter less than 45 μm) on bed fluidity was determined to get a base for good fluidization quality in the fluid catalytic cracking (FCC) unit. The fines content in equilibrium FCC catalysts (Ecat) from commercial units were controlled by adding or removing the fines to simulate commercial situation. To get the fluidity values (U_mb/U_mf) of seven different FCC catalysts (2 Ecats and 5 fresh catalysts) and their mixture, minimum fluidization velocity (U_mf) and minimum bubbling velocity (U_mb) were measured in a fluidized bed reactor (0.05 m ID). The fluidity decreased with loss of fines content and increased with increments of makeup of fresh catalysts or additive with the controlled fines content. The fluidities of catalysts increase with increases of normalized particle diameter variation by the fines addition. The obtained fluidities have been correlated with the fines contents and the catalyst and gas properties. The proposed correlation could guide to keep good catalyst fluidity in the FCC unit.

Sung M, et al. J Korean Med Sci. 2017 Jun;32(6):926-932. https://doi.org/10.3346/jkms.2017.32.6.926

Fluidized bed reactors have been increasingly applied for mass production of Carbon Nanotube (CNT) using catalytic chemical vapor deposition technology. Effect of particle size (d_p = 131 μm and 220 μm) on fluidization characteristics and aggregation behavior of the CNT particles have been determined in a fluidized bed for its design and scale-up. The CNT aggregation properties such as size and shape were measured in the dilute phase of a fluidized bed (0.15 m-ID × 2.6 m high) by the laser sheet technique for the visualization. Two CNT particle beds showed different tendency in variations of the aggregates factors with gas velocity due to differences in factors contributing to the aggregate formation. The CNT particles with a larger mean size presented as relatively larger in the aggregate size than the smaller CNT particles at given gas velocities. The aggregates from the large CNT particles showed a sharp increase in the aspect ratio and rapid decrease in the roundness and the solidity with gas velocity. A possible mechanism of aggregates formation was proposed based on the variations of aggregates properties with gas velocity. The obtained Heywood diameters of aggregates have been firstly correlated with the experimental parameter.

There is a growing interest in a fluidized bed particle receiver that directly irradiates sunlight to particles in the fluidized bed as a solar thermal collector for heating. Thermal performance of directly-irradiated fluidized bed gas heater is strongly affected by the physical properties of the particles. The effect of SiC particle size on heat transfer characteristics in the solar fluidized bed gas heater (50 mm-ID × 100 mm high) has been determined. The outlet gas temperatures showed a maximum value with increasing gas velocity due to the particles motion by bubble behavior in the bed, and the maximum values were found at 3.6 times of U_mf for fine SiC and less than 2.0 times of U_mf for coarse SiC. Heat absorption from the receiver increased with increasing gas velocity, showing with maximum 18 W for the fine SiC and 23 W for the coarse SiC at 4.5 times of U_mf. The thermal efficiency of the receiver increased with increasing gas velocity, but was affected by the content of finer particles. The maximum thermal efficiency of the receiver was 14% for fine SiC and 20% for coarse SiC within the experimental range, but showing higher for the fine SiC at the same gas velocity. A design consideration was proposed to improve the thermal efficiency of the system.