Phenolic derivatives are among the most important contaminants present in the environment. These compounds are used in several industrial processes to manufacture chemicals such as pesticides, explosives, drugs and dyes. They also are used in the bleaching process of paper manufacturing. Apart from these sources, phenolic compounds have substantial applications in agriculture as herbicides, insecticides and fungicides. However, phenolic compounds are not only generated by human activity, but they are also formed naturally, e.g., during the decomposition of leaves or wood. As a result of these applications, they are found in soils and sediments and this often leads to wastewater and ground water contamination. Owing to their high toxicity and persistence in the environment, both, the US Environmental Protection Agency (EPA) and the European Union have included some of them in their lists of priority pollutants. Current standard methods of phenolic compounds analysis in water samples are based on liquid–liquid extraction (LLE) while Soxhlet extraction is the most used technique for isolating phenols from solid matrices. However, these techniques require extensive cleanup procedures that are time-intensive and involve expensive and hazardous organic solvents, which are undesirable for health and disposal reasons. In the last years, the use of news methodologies such as solid-phase extraction (SPE) and solid-phase microextraction (SPME) have increased for the extraction of phenolic compounds from liquid samples. In the case of solid samples, microwave assisted extraction (MAE) is demonstrated to be an efficient technique for the extraction of these compounds. In this work we review the developed methods in the extraction and determination of phenolic derivatives in different types of environmental matrices such as water, sediments and soils. Moreover, we present the new approach in the use of micellar media coupled with SPME process for the extraction of phenolic compounds. The advantages of micellar media over conventional extractants are reduction of organic solvent, low cost, easy handling and shorter time procedures.

Organic ultraviolet (UV) filters are used in personal care products, but they are also added to industrial products and are constantly released to the environment. This study analyses the occurrence of 8 widely used organic UV filters in seawater from three beaches on the Gran Canaria Island (Spain) and in three wastewater treatment plants (WWTPs) by taking samples from influents and effluents. It also discusses the target compounds' post-treatment removal efficiencies. Sampling was carried out for 6 months and analytes were extracted by solid phase extraction with Sep-pak C18 cartridges. They were determined by ultra-high performance liquid chromatography coupled to mass spectrometry in tandem. The potential environmental hazard associated with the found concentrations was also assessed for marine organisms. Different target compounds were detected on the analysed beaches and in the wastewater. Benzophenone-3 (BP3) was the most recurrent compound in the seawater samples (frequency detection of 83%) and also in wastewater influents and effluents (measured in all the samples). However, the highest concentrations for seawater (172 μg L^-1) and influent wastewater (208 μg L^-1) corresponded to octocrylene, while methylene bis-benzotriazolyltetramethylbutylphenol was the compound most concentrated in secondary treatment effluent (34.0 μg L^-1) and BP3 in tertiary treatment effluent (8.07 μg L^-1). All the analysed samples showed that at least one target UV filter was present. Regarding the removal efficiencies of these compounds in the studied WWTPs, consistent differences between the target compounds were observed in influent concentration terms, where the average removal rates were higher than 50% for most of the compounds. Conventional treatment is unable to completely remove many studied compounds, while tertiary treatment acts as an additional elimination for some of them. An environmental hazard quotient above 1 was found for octocrylene, benzophenone-3 and 4-methylbenzylidene camphor, which indicates a potential high hazard for living species if these compounds are present.

Endocrine-disruptor compounds (EDCs) can mimic natural hormones and produce adverse effects in the endocrine functions by interacting with estrogen receptors. EDCs include both natural and synthetic chemicals, such as hormones, personal care products, surfactants, and flame retardants, among others. EDCs are characterised by their ubiquitous presence at trace-level concentrations and their wide diversity. Since the discovery of the adverse effects of these pollutants on wildlife and human health, analytical methods have been developed for their qualitative and quantitative determination. In particular, mass-based analytical methods show excellent sensitivity and precision for their quantification. This paper reviews recently published analytical methodologies for the sample preparation and for the determination of these compounds in different environmental and biological matrices by liquid chromatography coupled with mass spectrometry. The various sample preparation techniques are compared and discussed. In addition, recent developments and advances in this field are presented.