Heat transfer predictions in gas turbine engines have focused on cooling techniques and on the effects of various flow phenomena. The effects of wakes, passing shock waves and freestream turbulence have all been of primary interest to researchers. The focus of the work presented in this paper is to develop a turbulence grid capable of generating high intensity, large-scale turbulence for use in experimental heat transfer measurements in a transonic facility. The grid is desired to produce freestream turbulence characteristic of the flow exiting the combustor of advanced gas turbine engines. A number of techniques are discussed in this paper to generate high intensity, large length-scale turbulence for a transonic facility. Ultimately, the passive grid design chosen is capable of producing freestream turbulence with intensity of approximately 10–12% near the entrance of the cascade passages with an integral length-scale of 2 cm.
19 April 2021 in Journal of Thermal Science and Engineering Applications
Utilizing a neural network, individual down-axis images of combustion waves in the rotating detonation engine (RDE) can be classified according to the number of detonation waves present and their directional behavior. While the ability to identify the number of waves present within individual images might be intuitive, the further classification of wave rotational direction is a result of the detonation wave’s profile, which suggests its angular direction of movement. The application of deep learning is highly adaptive and, therefore, can be trained for a variety of image collection methods across RDE study platforms. In this study, a supervised approach is employed where a series of manually classified images is provided to a neural network for the purpose of optimizing the classification performance of the network. These images, referred to as the training set, are individually labeled as one of ten modes present in an experimental RDE. Possible classifications include deflagration, clockwise and counterclockwise variants of co-rotational detonation waves with quantities ranging from one to three waves, as well as single, double, and triple counter-rotating detonation waves. After training the network, a second set of manually classified images, referred to as the validation set, is used to evaluate the performance of the model. The ability to predict the detonation wave mode in a single image using a trained neural network substantially reduces computational complexity by circumnavigating the need to evaluate the temporal behavior of individual pixel regions throughout time. Results suggest that while image quality is critical, it is possible to accurately identify the modal behavior of detonation waves based on only a single image rather than a sequence of images or signal processing. Successful identification of wave behavior using image classification serves as a steppingstone for further machine learning integration in RDE research and development of comprehensive real-time diagnostics.
8 November 2016 in Journal of Thermal Science and Engineering Applications
An advanced, high-effectiveness film cooling design, the antivortex hole (AVH) has been investigated by several research groups and shown to mitigate or counter the vorticity generated by conventional holes and increase film effectiveness at high blowing ratios and low freestream turbulence levels. The effects of increased turbulence on an AVH geometry were previously investigated in a preliminary steady computational fluid dynamics (CFD) study by Hunley et al. on the film effectiveness and net heat flux reduction (NHFR) at high blowing ratio. The current paper presents the results of an extended numerical parametric study, which attempts to separate the effects of turbulence intensity and length scale on film cooling performance of the AVH concept at high blowing ratio (2.0) and density ratio (2.0). In this extended study, steady Reynolds-averaged Navier–Stokes (RANS) analysis was performed with turbulence intensities of 5, 10, and 20% and length scales based on cooling hole diameter of Λx/dm = 1, 3, and 6. Increasing turbulence intensity was shown to increase the centerline, span-averaged, and area-averaged adiabatic film cooling effectiveness and NHFR. Larger turbulent length scales in the steady RANS analysis were shown to have little to no effect on the centerline, span-averaged, and area-averaged adiabatic film cooling effectiveness and NHFR at lower turbulence levels, but moderate effect at the highest turbulence levels investigated. Heat transfer results were in good agreement with the findings from adiabatic cases from previous work. Unsteady RANS results also provided supplementary flow visualization for the AVH film cooling flow under varying turbulence levels.
14 September 2023 in Journal of Engineering for Gas Turbines and Power
Although inherently unstable, existing research in rotating detonation combustion supports its application in notionally steady processes resulting in greater availability compared to conventional, constant pressure combustion. Further improvements rely on a more in-depth understanding of system losses and identifying conditions which optimize device performance. Within this study, the presence and proportion of ideal and nonideal combustion regimes are compared across a variety of process conditions and wave modes. Large-scale data analysis seeks to summarize proportional heat release associated with commensal, parasitic, and detonative combustion averaged across individual traces of OH* chemiluminescent data acquired at the detonation plane. Means of regime partitioning based on the anatomy of the time-resolved OH* signal are proposed to ensure consistent analysis throughout the current and future studies concerning combustion regimes. Of particular interest is the possible influence of wave on the nonideal combustion in relative proportion to the desired detonation. Results showed improved percent detonation with increasing significance for the following trends: decreasing equivalence ratio, increasing wave count, decreasing wave velocity, and increasing detonation time. Increased wave number, brought on by decreased equivalence ratios and wave velocities, is thought to decrease fill region surface area, and therefore, decrease nonideal contact burning. Additional analysis is performed to consider possible trend variation due to the presence of stable galloping waves, which were found to have minimal influence on relative percent detonation values. The outcome of this study suggests operational states, which correspond to increased wave quantities for increased proportions of reactants consumed by the targeted detonative combustion regime.