Joe Briscoe

Dr. Joe Briscoe


Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications


7 December 2012 in Advanced Materials
Verified
Journal Article
Closed access
PDF file
SHSabina M. Hatch
Sabina M. Hatch
JBJoe Briscoe
Joe Briscoe
SDSteve Dunn
Steve Dunn

20 February 2015 in Angewandte Chemie International Edition
Verified
Journal Article
Closed access
PDF file
JBJoe Briscoe
Joe Briscoe
AMAdam Marinovic
Adam Marinovic
Marta SevillaMarta Sevilla
Marta Sevilla
SDSteve Dunn
Steve Dunn
MTMaria-Magdalena Titirici
Maria-Magdalena Titirici

14 August 2013 in Energy & Environmental Science
Verified
Journal Article
Closed access
PDF file
JBJoe Briscoe
Joe Briscoe
NJNimra Jalali
Nimra Jalali
PWPeter Woolliams
Peter Woolliams
MSMark Stewart
Mark Stewart
PWPaul M. Weaver
Paul M. Weaver
SDSteve Dunn
Steve Dunn
Electromechanical energy harvesting converts mechanical energy from the environment, such as vibration or human activity, into electrical energy that can be used to power a low power electronic device. Nanostructured piezoelectric energy harvesting devices, often termed nanogenerators, have rapidly increased in measured output over recent years. With these improvements nanogenerators have the potential to compete with more traditional micro- or macroscopic energy harvesting devices based on piezoelectric ceramics such as lead zirconate titanate (PZT), polymers such as polyvinylidene fluoride (PVDF) or electrostatic, electret or electromagnetic kinetic energy harvesters. Power output from a nanogenerator is most commonly measured through open-circuit voltage and/or short-circuit current, where power may be estimated from the product of these values. Here we show that such measures do not provide a complete picture of the output of these devices, and can be misleading when attempting to compare alternative designs. In order to compare the power output from a nanogenerator, techniques must be improved in line with those used for more established technologies. We compare ZnO nanorod/poly(methyl methacrylate) (PMMA) and ZnO nanorod/poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS) devices, and show that despite an open-circuit voltage nearly three times lower the ZnO/PEDOT:PSS device generates 150 times more power on an optimum load. In addition, it is shown that the peak voltage and current output can be increased by straining the device more rapidly and therefore time-averaged power, or time-integrated measures of output such as total energy or total charge should be calculated. Finally, the internal impedance of the devices is characterised to develop an understanding of their behaviour and shows a much higher internal resistance but lower capacitive impedance for the ZnO/PMMA device. It is hoped that by following more rigorous testing procedures the performance of nanostructured piezoelectric devices can be compared more realistically to other energy harvesting technologies and improvements can be rapidly driven by a more complete understanding of their behaviour.

2 February 2018 in Journal of Materials Chemistry C
Verified
Journal Article
Open access
PDF file
YTYing Tu
Ying Tu
SCShuqun Chen
Shuqun Chen
XLXuan Li
Xuan Li
JGJelena Gorbaciova
Jelena Gorbaciova
WGWilliam P. Gillin
William P. Gillin
JBJoe Briscoe
Joe Briscoe
ZnO is one of the most widely studied semiconductors due to its direct wide band gap and high exciton binding energy. Due to its ease of synthesis, robustness and low cost, ZnO has been applied in a wide range of devices, including nanogenerators, solar cells, and photodetectors. In this work, ZnO nanorods were synthesized in a single step using an aqueous method at temperatures below 100 °C. The nanorods were annealed in oxygen and nitrogen and a p-type polymer poly(3,4-ethylenedioxythiophene)polystyrene sulfonate (PEDOT:PSS) was spray coated onto the top of ZnO nanorods to form a p–n junction. The I–V characteristics of the device showed that the annealing atmosphere had a significant effect on the rectification ratio of the device. Further analysis using Mott–Schottky, photoluminescence, and X-ray photoelectron spectroscopy (XPS) indicated that oxygen vacancy concentration correlated well with the free electron density in ZnO as well as the rectification ratio of the p–n junction devices. Devices made with ZnO nanorods annealed in nitrogen had a better rectification ratio than oxygen, representing a simple method to improve p–n junction diode behaviour through tuning the defect properties of the nanorods via controlled annealing.