The search for low-cost and sustainable adsorbents for dye removal has driven the valorization of agro-industrial residues. In this study, pecan nutshells (PNSs) were evaluated as a biosorbent for methylene blue (MB) removal. The material was prepared by drying, grinding, and alkaline treatment with NaOH, which led to an increase in the apparent surface area (0.974 m2·g–1) and pore volume (0.0014 cm3·g–1). Surface characterization revealed the involvement of hydroxyl, carboxyl, and aromatic functional groups in the interaction with the dye molecules. The adsorption of MB by PNSs exhibited high efficiency, even at low dosages, and optimal performance was observed at 1.5 g·L–1. The process remained essentially pH-independent across the 4–10 range. Equilibrium data were analyzed using the Langmuir, Freundlich, Dubinin–Radushkevich, and Sips isotherm models. Among them, the Sips model provided the best fit to the experimental data, yielding a maximum adsorption capacity of 317.5 mg·g–1 at 25 °C, which is consistent with a heterogeneous surface presenting finite saturation. The thermodynamic parameters (ΔH° = +12.32 kJ·mol–1; ΔG° = −13.43 kJ·mol–1 at 25 °C; ΔS° = +86.27 J·mol–1·K–1) indicate that the adsorption process is spontaneous and endothermic, with an enthalpy change characteristic of weak to moderate interactions. Kinetic data were best described by the pseudo-second-order model, with equilibrium reached within approximately 180 min. Intraparticle diffusion analysis revealed a multistep adsorption involving an initial boundary-layer diffusion followed by a slower pore diffusion. Overall, the adsorption mechanism is interpreted as multifactorial, governed by hydrogen bonding, π–π stacking, and van der Waals forces, consistent with a physisorption-dominated process strengthened by structural heterogeneity. These results demonstrate that PNS combines high capacity with operational simplicity, representing a scalable and sustainable alternative for the treatment of dye-contaminated wastewater.
Polycyclic aromatic hydrocarbons (PAHs) are classified as persistent organic pollutants found in all environmental compartments and in certain concentrations may present health risks. This work compared the performance of high density polyethylene (HDPE) and polyurethane foam (PUF) for the removal of PAHs naphthalene (NAP), acenaphthylene, acenaphthene, fluorene, phenanthrene, anthracene (ANT), and chrysene (CHR) from individual aqueous solutions, relative to Amberlite XAD-2. Batch studies were performed at 20 °C and monitored via UV-Vis spectrophotometry. The effect of the organic modifier, amount of adsorbent, capacity, and adsorption kinetics were investigated. Using 10% acetonitrile as the organic modifier, the removal of ANT and CHR was greater than 90% in 0.5 g of HDPE and PUF. By reducing the amount of the three adsorbents to 0.1 g, the removal percentages did not change significantly – they remained above 90% for most PAHs. The greatest differences were for the CHR, which decreased from 87.5% to 37.6% in HDPE, 91.4% to 63.8% with PUF, and 86.9% to 47.8% in XAD-2. The adsorption capacity in the range of 0–180 min was governed by two stages: the first occurred within 60 min, where the sorption rates were higher; and the second, between 60 and 180 min, where practically no variations occurred. Kinetic data were analyzed by the pseudo-first order, pseudo-second order, and Weber and Morris models. With the exception of NAP, the pseudo-second-order model applies to all compounds. The values of k2 ranged from 0.19 to 1.46 (g mg−1 min−1) in HDPE, between 0.19 and 2.96 (g mg−1 min−1) for PUF and 0.10 and 3.20 (g mg−1 min−1) in XAD-2. The results demonstrate the viability of the HDPE and PUF polymers as easily available alternative materials to XAD-2.