María Teresa Hernández-Sierra

Dr. María Teresa Hernández-Sierra

Automotive Systems Engineering Division, Instituto Tecnológico Superior de Irapuato, Irapuato, Guanajuato, Mexico
orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 November 2019 in Applied Sciences
Verified
Journal Article
Open access
PDF file
María Teresa Hernández-SierraMaría Teresa Hernández-Sierra
María Teresa Hernández-Sierra
MBMicael Gerardo Bravo-Sánchez
Micael Gerardo Bravo-Sánchez
JBJosé E. Báez
José E. Báez
LALuis Daniel Aguilera-Camacho
Luis Daniel Aguilera-Camacho
JGJ. Santos García-Miranda
J. Santos García-Miranda
Karla Judith Moreno BelloKarla Judith Moreno Bello
Karla Judith Moreno Bello
Although much has been learned and investigated about environmentally friendly lubricants in recent years, several issues remain critical to their use in specific applications. A key point that could be limiting their utilization is that the effect of green lubricants on the tribological and mechanical properties of the elements has not been thoroughly studied since such attributes determine their performance in industrial applications. For this reason, in this research, the effect of green lubrication on the tribological and hardness properties of AISI 4140 steel was studied. The performance of three bio-based lubricants was studied and compared to that of five of the most representative lubricants. First, the lubricants were chemically and physically characterized. Then, the effect of each lubricant on the friction and wear behavior of the system was analyzed by kinetic friction coefficient, wear rate calculations, and microhardness measurements. In general, the bio-based lubricants exhibited the lowest values of friction and wear. Further the mechanical properties of the systems lubricated by these lubricants were not affected or were affected to a lesser degree.

6 June 2018 in Metals
Verified
Journal Article
Open access
PDF file
María Teresa Hernández-SierraMaría Teresa Hernández-Sierra
María Teresa Hernández-Sierra
LALuis Daniel Aguilera-Camacho
Luis Daniel Aguilera-Camacho
JBJosé E. Báez
José E. Báez
JGJ. Santos García-Miranda
J. Santos García-Miranda
Karla Judith Moreno BelloKarla Judith Moreno Bello
Karla Judith Moreno Bello
Lubricants have much importance in several industries, principally serving to reduce friction and wear in mechanical elements. In this study, the influence of Castor oil as bio-lubricant on the friction and wear performance of AISI 4140 steel was investigated. For that purpose, pin-on-disk friction tests were conducted according to ASTM G-99, by using pins of tungsten carbide (WC) as counterparts. The experiments were performed at two different temperatures. This work also presents the Attenuated Total Reflection Fourier Transform Infrared Spectroscopy (ATR-FTIR) and 1H-NMR analyses for the chemical characterization of oils and a study of their degradation by oxidation. The analysis of the damage caused to steel due to friction was deepened by analyzing its microhardness and microstructure in the worn zone. As a reference, the same experiments were performed with a commercial oil. The friction behavior of 4140 steel/WC with Castor oil lubrication at the two temperatures was notably better than that obtained under the reference oil lubrication. The kinetic friction coefficient (µk) was up to 76% lower. However, a slight increase in steel wear was observed under Castor oil lubrication. Despite this, these results suggest that Castor oil could be used as bio-lubricant in systems which are susceptible to levels of high friction.

19 September 2021 in Materials
Verified
Journal Article
Open access
PDF file
Karla Judith Moreno BelloKarla Judith Moreno Bello
Karla Judith Moreno Bello
María Teresa Hernández-SierraMaría Teresa Hernández-Sierra
María Teresa Hernández-Sierra
JBJosé E. Báez
José E. Báez
EREloy Rodriguez-deLeon
Eloy Rodriguez-deLeon
LALuis Daniel Aguilera-Camacho
Luis Daniel Aguilera-Camacho
JGJ. Santos García-Miranda
J. Santos García-Miranda
The present study focuses on an introductory analysis of the use of three xanthophylls as additives for green lubricant applications. For this purpose, the additives were characterized by FTIR and 1H-NMR techniques, and the bio-lubricants were described by their physical properties. The effect of the natural compounds on the friction and wear properties of bio-lubricants were evaluated by sliding friction tests under boundary conditions, as confirmed by an analysis of the lubricating film thickness. The antioxidant capacity was analyzed by FTIR spectroscopy. It was observed better wear protection in castor oil with xanthophylls than without these additives. The wear rate was reduced up to 50% compared with neat oil. Lesser beneficial effects were appreciated in friction coefficient since it was increased 25%. The best contribution was observed with astaxanthin as an additive. In addition, a significant improvement in the oxidation of castor oil, complemented with this additive, was exhibited by FTIR analysis. It was found that xanthophylls could be employed as additives for totally biodegradable lubricant applications since they have better tribological and antioxidant behavior than current additives.

13 August 2018 in Journal of Mechanical Science and Technology
Verified
Journal Article
Closed access
PDF file
María Teresa Hernández-SierraMaría Teresa Hernández-Sierra
María Teresa Hernández-Sierra
LAL. D. Aguilera-Camacho
L. D. Aguilera-Camacho
Arturo PonceArturo Ponce
Arturo Ponce
JGJ. Santos García-Miranda
J. Santos García-Miranda
Karla Judith Moreno BelloKarla Judith Moreno Bello
Karla Judith Moreno Bello

21 February 2022 in Metals
Verified
Journal Article
Open access
PDF file
Ricardo Ortega-ÁlvarezRicardo Ortega-Álvarez
Ricardo Ortega-Álvarez
María Teresa Hernández-SierraMaría Teresa Hernández-Sierra
María Teresa Hernández-Sierra
LALuis Daniel Aguilera-Camacho
Luis Daniel Aguilera-Camacho
MBMicael Gerardo Bravo-Sánchez
Micael Gerardo Bravo-Sánchez
Karla Judith Moreno BelloKarla Judith Moreno Bello
Karla Judith Moreno Bello
JGJ. Santos García-Miranda
J. Santos García-Miranda
There is a great need to perform all processes and services more efficiently to reduce energy consumption and material waste. Bearing systems are present in all machines and motors, playing an important role in the reduction of energy consumption. 100Cr6 (ISO 683-17:2014) and AISI 8620 are two typical steels employed in most bearing systems. However, improving the tribological performance of these steels is still required. This study reports the analysis of green lubricants based on mixtures of vegetable oils to improve the friction and wear properties of steel bearing systems. Firstly, a method is presented to identify potential mixtures based on the excess thermodynamic properties. Then, the tribological performance of the 100Cr6/8620 steel bearing system lubricated with the selected mixtures is evaluated by the ball-on-disk method. It was found that the friction and wear behavior of the 100Cr6/8620 steel bearing system can be notably improved by the utilization of oil mixtures rather than pure green oils. The kinetic friction coefficient decreased up to 10% with the ideal mixture of castor and sesame oil, while wear was reduced up to 81% with the ideal mixture of castor and canola oil. Therefore, we suggest that vegetable oil blends may be a good option for the feasible manufacture of biolubricants for bearing systems.

27 October 2022 in RSC Advances
Verified
Journal Article
Open access
PDF file
EREloy Rodriguez-deLeon
Eloy Rodriguez-deLeon
BMBah Moustapha
Bah Moustapha
JBJosé E. Báez
José E. Báez
María Teresa Hernández-SierraMaría Teresa Hernández-Sierra
María Teresa Hernández-Sierra
Karla Judith Moreno BelloKarla Judith Moreno Bello
Karla Judith Moreno Bello
KSKenneth Shea
Kenneth Shea
Three xanthophylls [(3R,3′R,6′R)-lutein (1), (3R,3′S)-zeaxanthin (2), and (3R,3′S)-astaxanthin (3)] were used for the first time as initiators in the ring-opening polymerization (ROP) of ε-caprolactone (CL) catalyzed by tin(II) 2-ethylhexanoate [Sn(Oct)2] for the synthesis of novel sustainable xanthophyll-containing poly(ε-caprolactone)s (xanthophylls-PCL). The obtained polyesters were characterized by 1H and 13C NMR, FT-IR, DSC, SEC, and MALDI-TOF MS, and their use as additives in green lubricants was evaluated using a sliding friction test under boundary conditions. Xanthophylls-PCL were obtained with good conversions and with molecular weights determined by SEC to be between 2500 and 10 500 Da. The thermal properties of xanthophyll-polyesters showed a crystalline domain, detected by DSC. Lastly, the green lubricant activity of these polymers was evaluated and the results showed that xanthophylls-PCL could be employed as additives for biodegradable lubricant applications since they have better tribological behavior than current additives, which demonstrates their potential as future commercial materials with interesting eco-friendly properties for diverse applications.