J. Santos García-Miranda

Dr. J. Santos García-Miranda

National Technological Institute of Mexico
orcid

Research Focus & Metrics

Academic Career Length

22Years (2005-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 January 2015 in Journal of Coatings Technology and Research
Verified
Journal Article
Closed access
PDF file
LALuis Daniel Aguilera-Camacho
Luis Daniel Aguilera-Camacho
CNCarolina Hernández Navarro
Carolina Hernández Navarro
Karla Judith Moreno BelloKarla Judith Moreno Bello
Karla Judith Moreno Bello
JGJ. Santos García-Miranda
J. Santos García-Miranda
AAA. Arizmendi-Morquecho
A. Arizmendi-Morquecho

1 April 2012 in Wear
Verified
Journal Article
Closed access
CNCarolina Hernández Navarro
Carolina Hernández Navarro
Karla Judith Moreno BelloKarla Judith Moreno Bello
Karla Judith Moreno Bello
ACA. Chávez-Valdez
A. Chávez-Valdez
FLF. Louvier-Hernández
F. Louvier-Hernández
JGJ. Santos García-Miranda
J. Santos García-Miranda
AAA. Arizmendi-Morquecho
A. Arizmendi-Morquecho

15 November 2019 in Applied Sciences
Verified
Journal Article
Open access
PDF file
María Teresa Hernández-SierraMaría Teresa Hernández-Sierra
María Teresa Hernández-Sierra
MBMicael Gerardo Bravo-Sánchez
Micael Gerardo Bravo-Sánchez
JBJosé E. Báez
José E. Báez
LALuis Daniel Aguilera-Camacho
Luis Daniel Aguilera-Camacho
JGJ. Santos García-Miranda
J. Santos García-Miranda
Karla Judith Moreno BelloKarla Judith Moreno Bello
Karla Judith Moreno Bello
Although much has been learned and investigated about environmentally friendly lubricants in recent years, several issues remain critical to their use in specific applications. A key point that could be limiting their utilization is that the effect of green lubricants on the tribological and mechanical properties of the elements has not been thoroughly studied since such attributes determine their performance in industrial applications. For this reason, in this research, the effect of green lubrication on the tribological and hardness properties of AISI 4140 steel was studied. The performance of three bio-based lubricants was studied and compared to that of five of the most representative lubricants. First, the lubricants were chemically and physically characterized. Then, the effect of each lubricant on the friction and wear behavior of the system was analyzed by kinetic friction coefficient, wear rate calculations, and microhardness measurements. In general, the bio-based lubricants exhibited the lowest values of friction and wear. Further the mechanical properties of the systems lubricated by these lubricants were not affected or were affected to a lesser degree.

6 June 2018 in Metals
Verified
Journal Article
Open access
PDF file
María Teresa Hernández-SierraMaría Teresa Hernández-Sierra
María Teresa Hernández-Sierra
LALuis Daniel Aguilera-Camacho
Luis Daniel Aguilera-Camacho
JBJosé E. Báez
José E. Báez
JGJ. Santos García-Miranda
J. Santos García-Miranda
Karla Judith Moreno BelloKarla Judith Moreno Bello
Karla Judith Moreno Bello
Lubricants have much importance in several industries, principally serving to reduce friction and wear in mechanical elements. In this study, the influence of Castor oil as bio-lubricant on the friction and wear performance of AISI 4140 steel was investigated. For that purpose, pin-on-disk friction tests were conducted according to ASTM G-99, by using pins of tungsten carbide (WC) as counterparts. The experiments were performed at two different temperatures. This work also presents the Attenuated Total Reflection Fourier Transform Infrared Spectroscopy (ATR-FTIR) and 1H-NMR analyses for the chemical characterization of oils and a study of their degradation by oxidation. The analysis of the damage caused to steel due to friction was deepened by analyzing its microhardness and microstructure in the worn zone. As a reference, the same experiments were performed with a commercial oil. The friction behavior of 4140 steel/WC with Castor oil lubrication at the two temperatures was notably better than that obtained under the reference oil lubrication. The kinetic friction coefficient (µk) was up to 76% lower. However, a slight increase in steel wear was observed under Castor oil lubrication. Despite this, these results suggest that Castor oil could be used as bio-lubricant in systems which are susceptible to levels of high friction.

1 January 2013 in Progress in Organic Coatings
Verified
Journal Article
Closed access
VMV. Morales-Nieto
V. Morales-Nieto
CNCarolina Hernández Navarro
Carolina Hernández Navarro
Karla Judith Moreno BelloKarla Judith Moreno Bello
Karla Judith Moreno Bello
AAA. Arizmendi-Morquecho
A. Arizmendi-Morquecho
ACA. Chávez-Valdez
A. Chávez-Valdez
JLJ.F. Louvier-Hernández
J.F. Louvier-Hernández

27 January 2012 in Journal of Plastic Film & Sheeting
Verified
Journal Article
Closed access
CNCarolina Hernández Navarro
Carolina Hernández Navarro
Karla Judith Moreno BelloKarla Judith Moreno Bello
Karla Judith Moreno Bello
AAAna Arizmendi-Morquecho
Ana Arizmendi-Morquecho
ACAlejandra Chávez-Valdez
Alejandra Chávez-Valdez
JGJ. Santos García-Miranda
J. Santos García-Miranda
We prepared a chitosan/hydroxyapatite composite as coating on ultra–high-molecular-weight polyethylene substrates. The hydroxyapatite was prepared by a precipitation method obtaining particles with nanometer sizes with needle and spherical morphologies. The coating was prepared by a mixture of hydroxyapatite and lower molecular weight chitosan. Fourier transformed infrared spectroscopy technique was used to study the hydroxyapatite synthesis and composite coating. The chitosan/hydroxyapatite coating has been compared with a pure chitosan coating on ultra–high-molecular-weight polyethylene substrate in order to study the influence of hydroxyapatite incorporation. The characterization of coating thickness was performed by light microscopy, whereas the surface morphology was characterized by scanning electron microscopy. A ball-on-disc tribometer, employing a 6-mm diameter tungsten carbide ball, was run as a test method to investigate tribological behaviors of the chitosan/hydroxyapatite and chitosan coatings in dry conditions. It was found that the friction coefficients of the chitosan/hydroxyapatite coating have lower values than chitosan coating. The chitosan/hydroxyapatite coating exhibited lower wear rate values than the chitosan coating. The incorporation of hydroxyapatite nanoparticles into chitosan increased the coating thickness from 20 µm to 37 µm. We have found a composite hardness of 9.1 HV and 6.4 HV for the chitosan and chitosan/hydroxyapatite coating, respectively.