In the present work, we investigated the acetone sensing characteristics and mechanism of SnO2 thick-films through experiments and DFT calculations. SnO2 thick film annealed at 600 °C could sensitively detect acetone vapors. At the optimum operating temperature of 180 °C, the responses of the SnO2 sensor were 3.33, 3.94, 5.04, and 7.27 for 1, 3, 5, and 10 ppm acetone, respectively. The DFT calculation results show that the acetone molecule can be adsorbed on the five-fold-coordinated Sn and oxygen vacancy (VO) sites with O-down, with electrons transferring from acetone to the SnO2 (110) surface. The acetone molecule acts as a donor in these modes, which can explain why the resistance of SnO2 or n-type metal oxides decreased after the acetone molecules were introduced into the system. Molecular dynamics calculations show that acetone does not convert to other products during the simulation.
The synthesized LaFeO3 nanocrystalline sensor powders show positive response to sensing acetone vapor at 200 °C. The responses to acetone vapor (at 0.5, 1, 2, 5, 10 ppm) are 1.18, 1.22, 1.89, 3.2 and 7.83. To make the sensor operate at a lower optimum temperature, UV light illumination 365 nm is performed. Response of the sensor has a larger improvement under 365 nm UV light illumination than without it. The responses to acetone vapor (at 0.5, 1, 2, 5, 10 ppm) are 1.37, 1.85, 3.16, 8.32 and 14.1. Furthermore, the optimum operating temperature is reduced to 170 °C. As the relative humidity increases, the resistance and sensitivity of sensor are reduced. The sensor shows good selectivity toward acetone when compared with other gases. Since the detection of ultralow concentrations of acetone vapor is possible, the sensor can be used to preliminarily judge diabetes in the general public, as a high concentration of acetone is exhaled in breath of diabetic patients. The sensor shows a good stability, which is further enhanced under UV light illumination. The sensor shows better stability when under 365 nm UV light illumination. Whether under light illumination or not. The LaFeO3 material shows good performance as a sensor when exposed to acetone vapor.
Au:SmFe0.9Zn0.1O3 is synthesized by a sol-gel method and annealed at 750 °C. Through XRD, SEM and XPS analysis methods, the microstructure of the material has been observed. The average particle size is about 50 nm. The sensor shows a high sensitivity toward acetone vapor. As the relative humidity increases, the resistance and sensitivity of the sensor decline. To obtain a low optimum operating temperature, light illumination with different wavelengths has been introduced. The sensitivity toward acetone is improved at lower operating temperature when the sensor is irradiated by light. The smaller the wavelengths, the better the sensitivity of the sensor. Compared with other gases, the sensor shows excellent selectivity to acetone vapor, with better sensitivity, selectivity and stability when under light illumination.
Nanocomposites of SmFeO3/YFeO3 (1:0, 0.8:0.2, 0.6:0.4, 0.4:0.6, 0.2:0.8, and 0:1) with different molar proportions were prepared by the sol–gel method. The material’s properties were characterized by various test methods, such as scanning-electron microscopy (SEM) and X-ray photoelectron-diffraction spectrometry (XPS). The gas-sensing characteristics of the sensor were tested in darkness and under illumination using monochromatic light with various selected wavelengths. The test results show that the SmFeO3/YFeO3 sensor with the molar ratio of 0.4:0.6 had the highest gas response to volatile organic compound (VOC) gases and that the optimum operating temperature was lower (120 °C). The light illumination improved the sensor’s sensitivity to gas. Under the 370-nanometer light illumination, the sensor’s responses to 30 ppm of ethanol, acetone, and methanol gases were 163.59, 134.02, and 111.637, respectively, which were 1.35, 1.28, and 1.59 times higher, respectively, than those without light. The high gas sensitivity of the sensor was mainly due to the adsorption of oxygen on the material’s surface and the formation of a p–p heterojunction. The SmFeO3/YFeO3 sensor, which can respond to different VOC gases, can be used to detect the safety of unknown environments and provide a timely warning of the presence of dangerous gases in working environments.