Falling is ranked highly among the threats in elderly healthcare, which promotes the development of automatic fall detection systems with extensive concern. With the fast development of the Internet of Things (IoT) and Artificial Intelligence (AI), camera vision-based solutions have drawn much attention for single-frame prediction and video understanding on fall detection in the elderly by using Convolutional Neural Network (CNN) and 3D-CNN, respectively. However, these methods hardly supervise the intermediate features with good accurate and efficient performance on edge devices, which makes the system difficult to be applied in practice. This work introduces a fast and lightweight video fall detection network based on a spatio-temporal joint-point model to overcome these hurdles. Instead of detecting fall motion by the traditional CNNs, we propose a Long Short-Term Memory (LSTM) model based on time-series joint-point features extracted from a pose extractor . We also introduce the increasingly mature RGB-D camera and propose 3D pose estimation network to further improve the accuracy of the system. We propose to apply tensor train decomposition on the model to reduce storage and computational consumption so the deployment on edge devices can to realized. Experiments are conducted to verify the proposed framework. For fall detection task, the proposed video fall detection framework achieves a high sensitivity of 98.46% on Multiple Cameras Fall, 100% on UR Fall, and 98.01% on NTU RGB-D 120. For pose estimation task, our 2D model attains 73.3 mAP in the COCO keypoint challenge, which outperforms the OpenPose by 8%. Our 3D model attains 78.6% mAP on NTU RGB-D dataset with 3.6× faster speed than OpenPose.
18 August 2025 in ACM Transactions on Reconfigurable Technology and Systems
Transformer-based models have achieved extensive success with increasingly large numbers of parameters and computations, for which many multi-core accelerators have been developed. Nevertheless, they suffer from limited throughput due to either low operating frequency or high communication overhead between cores. This article proposes an FPGA-based multi-core overlay processor, named MCoreOPU, to optimize intra-core computation and inter-core communication. First, we boost the operating frequency of the processing element (PE) array to double the rest of the processor to improve the intra-core throughput. Second, we develop on-chip synchronization routers to reduce off-chip memory traffic, where only the partial sum and maximum are communicated between cores rather than entire vectors for layer normalization and softmax. Moreover, we pipeline synchronization to reduce synchronization latency and develop a bypass of the interconnect bus to reduce the off-chip memory access latency. Finally, we optimize the multi-core model allocation and scheduling to minimize the inter-core communications and maximize the intra-core computation efficiency. The MCoreOPU is implemented in 8-bit fixed-point precision with four cores and four DDRs on the Xilinx U200 FPGA, where the PE array runs at 600 MHz while the rest runs at 300 MHz. Experimental results show that the throughput per MAC of MCoreOPU for BERT, ViT, GPT-2, and LLaMA inference is 1.31 \(\times\) –7.18 \(\times\) higher than other FPGA-based accelerators. Compared with the A100 GPU, the throughput per equivalent MAC efficiency is improved by 22.52 \(\times\) –27.12 \(\times\) .
In thin film solar cells, the semiconductor materials usually contain multiple impurity/defect states as donor or acceptor dopants. The local charge neutrality (LCN) condition determines the equilibrium Fermi (EF) level and concentration of electrons and holes. However, the equation of LCN is a transcendental equation of EF. It is impossible to find its analytical solution and we can only solve it by graphic or numerical method. A simple approximate graphic method (GM) used for estimation of majority carrier compensation of semiconductors with multiple donors and acceptors was proposed by Chin. By introducing the concept of ranking the dopants and the wrapping step function, dopants concentration and Fermi level could be obtained easily. In this paper, we analyze the graphic method and propose a new numeric graphic method (NGM) based on GM. In addition, comparison of NGM with NM and analytics of the accuracy of GM are presented. With numerical calculation, some procedures of GM extending the application of GM are improved.