The practical problems of existing methods of walnut cracking under compression loading, including incomplete walnut-shell crushing, broken walnut kernels, and so on, are widespread in walnut processing and are constraints that hinder mechanized walnut processing. Therefore, attempts have been made to design and optimize a multi-point extrusion walnut cracking device. For this, walnuts were fed manually into a cracking unit through the hopper. The tangential force of the grading roller graded the walnuts and dropped them into the gap between the rotating cracking roller and extrusion plate, causing them to crack. The developed machine was tested and the parameters were optimized using a central composite design (CCD). The objective functions involving the cracking angle (CA: 0.17, 0.27, 0.52, 0.76, 0.86°) and roller speed (RS: 63, 75, 105, 135, 147 r/min) were calculated. The shell cracking rate (SCR), whole kernel rate (WKR), and specific energy consumption (Es) regression models were established using the quadratic regression orthogonal combination test and the parameters were optimized using MATLAB software. The results showed that the most significant factors for the RS were the linear terms of the SCR and WKR, whereas for the CA the most significant factor was the linear term of the Es. The interaction term of the two factors had a significant effect on the three indicators. The optimal parameter combination was determined to be 0.47° for the CA and 108 r/min for the RS. On this basis, the adaptability test showed that the cracking device had a better cracking effect on walnuts with a gap between the walnut shell and kernel greater than 1.6 mm and a shell thickness less than 1.2 mm. The results have practical significance for the design of walnut cracking devices.
This study aims to characterize the emissions of ammonia (NH3) and methane (CH4) from naturally ventilated dairy barns located in cold regions during the winter season, thereby providing a scientific basis for optimizing dairy barn environmental management. The target barn was selected at a commercial dairy farm in Ulanchab, Inner Mongolia, China. Environmental factors, including temperature, humidity, wind speed, and concentrations of NH3, CH4, and CO2, were monitored both inside and outside the barn. The ventilation rate and emission rate were calculated using the CO2 mass balance method. Additionally, NH3 and CH4 emission prediction models were developed using the adaptive neural fuzzy inference system (ANFIS). Correlation analyses were conducted to clarify the intrinsic links between environmental factors and NH3 and CH4 emissions, as well as the degree of influence of each factor on gas emissions. The ANFIS model with a Gaussian membership function (gaussmf) achieved the highest performance in predicting NH3 emissions (R2 = 0.9270), while the model with a trapezoidal membership function (trapmf) was most accurate for CH4 emissions (R2 = 0.8977). The improved ANFIS model outperformed common models, such as multilayer perceptron (MLP) and radial basis function (RBF). This study revealed the significant effects of environmental factors on NH3 and CH4 emissions from dairy barns in cold regions and provided reliable data support and intelligent prediction methods for realizing the precise control of gas emissions.
1 January 2025 in International Journal of Agricultural and Biological Engineering
Walnut shell-kernel separation after cracking is crucial for providing raw materials for further processing. However, impurities and losses during separation limit complete separation. To address this, a two-stage tandem separation device was designed and optimized. Computational fluid dynamics (CFD) was used to analyze the effects of four bent duct structures on the flow field. Response surface methodology (RSM) and artificial neural networks (ANN) were employed to predict separation performance under various conditions. Both models accurately predicted performance, with ANN showing superior predictive ability. The optimal design was determined using non-dominated sorting genetic algorithm-II (NSGA-II) and technique for order preference by similarity to an ideal solution (TOPSIS): the inclination of the first stage deflector plate (x 1) was 39°,the inclination of the second stage deflector plate (x 2) was 36°, the wind speed of the first stage fan (x 3) was 21 m/s, and the wind speed of the second stage fan (x 4) was 13.5 m/s; impurity rate (y 1) was 4.51%, and loss rate (y 2) was 6.62%. Compared with traditional single-stage devices, the optimized device reduced impurity rate by 73.98% to 77.55% and loss rate by 9.44% to 53.96%, significantly improving separation efficiency and quality. This study provides theoretical guidance for designing and optimizing shell-kernel separation devices.
28 May 2026 in Computers and Electronics in Agriculture