Rapid and efficient demulsification (destabilizing of an emulsion) processes of a water in oil (W/O) emulsion were carried out in a three-dimensional electric spiral plate-type microchannel (3D-ESPM). In this experiment, the demulsifying efficiency of emulsions by 3D-ESPM was compared with that by gravity settling, the factors influencing demulsifying efficiency were investigated, and the induction period, cut size and residence time in the demulsification process were studied. The results showed that in contrast to the gravity settling method, 3D-ESPM can directly separate the disperse phase (water) instead of the continuous phase (oil). The maximum demulsifying efficiency of W/O emulsion in a single pass through the 3D-ESPM reached 90.3%, with a microchannel height of 200 μm, electric field intensity of 250 V /cm, microchannel angle of 180°, microchannel with 18 plates and a flow rate of 2 mL /min. An induction period of 0.6 s during the demulsification process was simulated with experimental data fitting. When the residence time of emulsion in 3D-ESPM was longer than the induction period, its demulsifying efficiency increased as the increase of the flow velocity due to the droplet coalescence effects of Dean vortices in the spiral microchannel. For this device a cut size of droplets of 4.5 μm was deduced. Our results showed that the demulsification process of W/O emulsion was intensified by 3D-ESPM based on the coupling effect between electric field-induced droplets migration and microfluidic hydrodynamic trapping.
A microreactor (MR) with a vaporization microchamber and a sinusoidal wave microchannel was fabricated to synthesize 2-cyanopyrazine (CP) directly with an aqueous 2-methylpyrazine (MP) solution. A continuous-flow process with high space-time yield was achieved under the premise of strong exothermality of this ammoxidation reaction. The vanadium metal oxide catalysts with four different supports (α-Al2O3, γ-Al2O3, ZSM-5(50), ZSM-5(80)) were evaluated by simply stacking in the wave microchannel from 350 to 540 °C. The process parameters (temperature, reactant ratio, and size of catalysts) were optimized with the selected CrVPO/γ-Al2O3 catalyst, and an optimal ammoxidation process with MP conversion (XMP) of 71.5% and CP selectivity (SCP) of 93.7% was obtained by a volume space velocity (GHSV) of 13 081 h–1 at 480 °C. Correspondingly, the space-time yield of CP (STYCP) was 1724–77 082 gCPkgcat–1h–1, which was the highest value ever reported for this reaction. Meanwhile, the ammoxidation reaction showed a great continuous-synthesis stability of 50-h running in the microreactor with the CP yield (YCP) remaining 56%–68%.
This study develops a high-performance water-based mold release agent for polyurethane (PU) foaming applications. We demonstrate that incorporating octamethylcyclotetrasiloxane (D4) into a dimethyl silicone oil emulsion (5 vol% fixed concentration) significantly enhances key performance metrics. By systematically varying D4 content (0–15 vol%), we characterize droplet morphology, particle size distribution, contact angle, and viscosity to elucidate the underlying enhancement mechanism. Our findings reveal the following: (i) Optimal emulsion stability: At 5 vol% D4, the mold release agent exhibits a narrow particle size distribution (6–9 μm). (ii) Efficient processing: Film formation completes within 10 min, reducing demolding force and yielding PU foam with defect-free, non-adherent surfaces. (iii) Storage stability: After 60 days in ambient conditions, performance remains unchanged, with no phase separation observed under thermal stress (60 °C) or refrigeration (2–6 °C). This work explores an alternative pathway to mitigate key limitations—slow film formation and poor shelf-life—offering a prototype for next-generation release agents.
A rectangular cup with a small radius at the bottom circular arc is a common sheet metal structure in aerospace components. However, when aluminum alloy plates are used for deep drawing of this type of rectangular cups, the wall thickness around the bottom circular arc is severely decreased. Hence, in this paper, locally-thickened plates were adopted for deep drawing of aluminum alloy rectangular cups with a relatively small radius at the bottom circular arc. The effect of thickening parameters of a locally-thickened plate on the radius at the bottom circular arc and the forming load was investigated by employing finite element simulations and deep drawing experiments. The results indicate that a smaller radius at the bottom circular arc is obtained by increasing the angle or reducing the thickness of the thickened convex rib of a plate. Moreover, the aforementioned is achieved when the side length of the thickened convex rib is equal to the punch width. The forming load is closely related to the thickening parameters of a locally-thickened plate. A small radius of 5 mm at the bottom circular arc was successfully obtained by optimizing the thickening parameters. Furthermore, the forming load during the deep drawing was significantly reduced.