Hydrogen detection with rapid response and ultra-low detection limits remains a critical challenge for safety and energy applications. Here, we report a fullerene-decorated PdCo nano-resistor network sensor that integrates nanostructuring, alloying, and surface-engineering approaches. The C 60 layer enhances sensor performance by increasing the surface-to-volume ratio, enabling fast hydrogen diffusion, relieving mechanical stress during cycling, and guiding nanostructure morphology. Our composite device (20 nm C 60 /3 nm Teflon AF/5 nm Pd 63 Co 37 /30 nm Teflon AF) achieves a response time of 0.40 ± 0.06 s across 1–100 mbar H 2 and detects 40 ppb H 2 with a signal-to-noise ratio of 10 at room temperature. A poly(methyl methacrylate) (PMMA) topcoat further improves cycling stability and selectivity under 90% relative humidity and interfering gases. This design provides a scalable approach and opens the door to future adaptation of porous carbon-based frameworks and polymeric interlayers to realize robust, high-performance hydrogen sensors for real-world applications.
Palladium (Pd) and titanium (Ti) exhibit opposite dielectric responses upon hydrogenation, with stronger effects observed in the near-infrared (NIR) region. Leveraging this contrast, we investigated Ti/Pd bilayer thin films as a platform for NIR hydrogen sensing—particularly at telecommunication-relevant wavelengths, where such devices have remained largely unexplored. Ti/Pd bilayers coated with Teflon AF (TAF) and fabricated via sequential electron-beam and thermal evaporation were characterized using optical transmission measurements under repeated hydrogenation cycles. The Ti (5 nm)/Pd (x = 2.5 nm)/TAF (30 nm) architecture showed a 2.7-fold enhancement in the hydrogen-induced optical contrast at 1550 nm compared to Pd/TAF reference films, attributed to the hydrogen ion exchange between the Ti and Pd layers. The optimized structure, with a Pd thickness of x = 1.9 nm, exhibited hysteresis-free sensing behavior, a rapid response time ( < 0.35 s at 4% ), and a detection limit below 10 ppm. It also demonstrated excellent selectivity with negligible cross-sensitivity to , , and CO, as well as high durability, showing less than 6% signal degradation over 135 hydrogenation cycles. These findings establish a scalable, room-temperature NIR hydrogen sensing platform with strong potential for deployment in automotive, environmental, and industrial applications.
We present a novel hydrogen (H 2 ) sensor based on a hexagonal PdCo composite nano-resistance network, featuring an innovative layered nanostructure and advanced materials. This state-of-the-art PdCo network is deposited on a thin layer of nanoporous fullerene C 60 -coated glass substrate using a combination of nanosphere lithography and the glancing angle codeposition (GLACD) technique, which significantly enhances the quality, morphology, and surface-to-volume ratio of the PdCo sensing elements to their full potential. Remarkably, this approach not only simultaneously improves the sensor's response time and sensitivity but also effectively mitigates the clamping effect. Our results demonstrate that the sensor, composed of a 20 nm C 60 /5 nm Pd 63 Co 37 /30 nm Teflon AF composite hole array, achieves a response time (t 90 ) of ≤ 0.8 seconds across the 1 – 100 mbar H 2 pressure range, with a limit of detection (LOD) of 40 parts per billion (ppb). Remarkably, when the Pd 63 Co 37 sensing layer is sandwiched by two TAF layers, the t 90 and LOD reach 0.36 s at 1 mbar H 2 and ~100 parts per trillion (ppt) H 2 , respectively. Additionally, when coated with an additional layer of Poly(methyl methacrylate) (PMMA), the sensor maintains robustness over hundreds of hydrogen cycling and aging effects and remains resilient against interference from gases such as CO 2 , CH 4 , and CO, as well as up to 90% relative humidity (RH). This low-cost, lightweight, and low-power hydrogen sensor platform holds significant potential to meet the stringent sensing requirements for automotive applications, concentration control, and environmental monitoring.
Palladium (Pd) and titanium (Ti) exhibit opposite dielectric responses upon hydrogenation, with stronger effects observed in the near-infrared (NIR) region. Leveraging this contrast, we investigate Ti/Pd bilayer thin films as a platform for NIR hydrogen sensing—particularly at telecommunication-relevant wavelengths, where such devices remain largely unexplored. Ti/Pd bilayers, coated with Teflon AF (TAF) and fabricated via sequential electron-beam evaporation, were characterized using optical transmission measurements under repeated hydrogenation cycles. The Ti (5 nm) / Pd (x = 2.5 nm) / TAF (30 nm) architecture shows a 2.7 times enhancement in hydrogen-induced optical contrast at 1550 nm compared to Pd/TAF reference films, attributed to hydrogen ion exchange between the Ti and Pd layers. The optimized structure, with Pd thickness of x = 1.9 nm, exhibits hysteresis-free sensing behavior, a rapid response time (t90 < 0.35 s at 4% H2), and a detection limit below 10 ppm. It also demonstrates excellent selectivity with negligible cross-sensitivity to CO2, CH4, and CO, as well as high durability, showing less than 6% signal degradation over 135 hydrogenation cycles. These findings establish a scalable, room-temperature NIR hydrogen sensing platform with strong potential for deployment in automotive, environmental, and industrial applications.