Valentina Donadei

Ms. Valentina Donadei

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 November 2020 in Nano Letters
Verified
Journal Article
Open access
WWWilliam S. Y. Wong
William S. Y. Wong
KHKatharina I. Hegner
Katharina I. Hegner
VDValentina Donadei
Valentina Donadei
LHLukas Hauer
Lukas Hauer
ANAbhinav Naga
Abhinav Naga
DVDoris Vollmer
Doris Vollmer
Slippery lubricant-infused surfaces (SLIPS) have shown great promise for anti-frosting and anti-icing. However, small length scales associated with frost dendrites exert immense capillary suction pressure on the lubricant. This pressure depletes the lubricant film and is detrimental to the functionality of SLIPS. To prevent lubricant depletion, we demonstrate that interstitial spacing in SLIPS needs to be kept below those found in frost dendrites. Densely packed nanoparticles create the optimally sized nanointerstitial features in SLIPS (Nano-SLIPS). The capillary pressure stabilizing the lubricant in Nano-SLIPS balances or exceeds the capillary suction pressure by frost dendrites. We term this concept capillary balancing. Three-dimensional spatial analysis via confocal microscopy reveals that lubricants in optimally structured Nano-SLIPS are not affected throughout condensation (0 °C), extreme frosting (−20 °C to −100 °C), and traverse ice-shearing (−10 °C) tests. These surfaces preserve low ice adhesion (10–30 kPa) over 50 icing cycles, demonstrating a design principle for next-generation anti-icing surfaces.

23 June 2018 in Materials
Verified
Journal Article
Open access
PDF file
VDValentina Donadei
Valentina Donadei
Francesca LionettoFrancesca Lionetto
Francesca Lionetto
MWMichael Wielandt
Michael Wielandt
AOArnt Offringa
Arnt Offringa
Alfonso MaffezzoliAlfonso Maffezzoli
Alfonso Maffezzoli
The causes of delamination and porosities during press forming of pre-consolidated flat laminates (blanks) made of carbon fiber-reinforced poly(ether ketone ketone) (PEKK) were addressed in this study. In particular, the quality of the blank laminate was investigated before and after infrared heating. The consolidation quality was evaluated by thickness measurements, non-destructive inspection (NDI), and optical microscopy. The experimental results confirmed that deconsolidation phenomena can be related to residual stresses formed during blank forming in an autoclave, then released during infrared heating (IR) of the blank, determining most of the defects in IR heated blanks. These defects, generated at the pre-heating stage, were not fully removed in the consolidation stage of the press forming process. An annealing treatment, performed on autoclave-consolidated blanks above the glass transition temperature of the matrix, was proposed to reduce the formation of defects during IR heating. The stress relaxation phenomena during annealing were modelled using a simple viscoelastic model.

1 March 2021 in ACS Nano
Verified
Journal Article
Open access
LHLukas Hauer
Lukas Hauer
WWWilliam S. Y. Wong
William S. Y. Wong
VDValentina Donadei
Valentina Donadei
KHKatharina I. Hegner
Katharina I. Hegner
Lou KondicLou Kondic
Lou Kondic
DVDoris Vollmer
Doris Vollmer
Frost is ubiquitously observed in nature whenever warmer and more humid air encounters colder than melting point surfaces (e.g., morning dew frosting). However, frost formation is problematic as it damages infrastructure, roads, crops, and the efficient operation of industrial equipment (i.e., heat exchangers, cooling fins). While lubricant-infused surfaces offer promising antifrosting properties, underlying mechanisms of frost formation and its consequential effect on frost-to-surface dynamics remain elusive. Here, we monitor the dynamics of condensation frosting on micro- and hierarchically structured surfaces (the latter combines micro- with nano- features) infused with lubricant, temporally and spatially resolved using laser scanning confocal microscopy. The growth dynamics of water droplets differs for micro- and hierarchically structured surfaces, by hindered drop coalescence on the hierarchical ones. However, the growth and propagation of frost dendrites follow the same scaling on both surface types. Frost propagation is accompanied by a reorganization of the lubricant thin film. We numerically quantify the experimentally observed flow profile using an asymptotic long-wave model. Our results reveal that lubricant reorganization is governed by two distinct driving mechanisms, namely: (1) frost propagation speed and (2) frost dendrite morphology. These in-depth insights into the coupling between lubricant flow and frost formation/propagation enable an improved control over frosting by adjusting the design and features of the surface.

11 November 2019 in Journal of Thermal Spray Technology
Verified
Journal Article
Open access
PDF file
VDValentina Donadei
Valentina Donadei
Heli KoivuluotoHeli Koivuluoto
Heli Koivuluoto
ESEssi Sarlin
Essi Sarlin
Petri VuoristoPetri Vuoristo
Petri Vuoristo
The present work investigates the effect of different process parameters on the production of low-density polyethylene (LDPE) coatings by flame spray technology. Previously, flame spraying of polymers has been successfully performed to obtain durable icephobic coatings, providing an interesting solution for applications facing icing problems, e.g. in marine, aviation, energy, and transportation industry. However, the fine tailoring of the process parameters represents a necessary strategy for optimising the coating production due to the unique thermal properties of each polymer. For this purpose, we vary the heat input of the process during flame spraying of the coating, by changing the transverse speed and the spraying distance. The results show that the variation in the process parameters strongly influenced the quality of the polymer coating, including its areal roughness, thickness, chemical composition, thermal stability, and degree of crystallinity. Furthermore, we demonstrate that these properties significantly affect the icephobic behaviour of the surface within the spray window of the chosen parameters. In conclusion, the relationship between the thermal degradation of the polymer and the icephobicity of the surface was defined. This highlights the importance of process parameter optimisation in order to achieve the desired icephobic performance of the LPDE coatings.

1 February 2022 in Progress in Organic Coatings
Verified
Journal Article
Open access
VDValentina Donadei
Valentina Donadei
Heli KoivuluotoHeli Koivuluoto
Heli Koivuluoto
ESEssi Sarlin
Essi Sarlin
HNHenna Niemelä-Anttonen
Henna Niemelä-Anttonen
TVTommi Varis
Tommi Varis
Petri VuoristoPetri Vuoristo
Petri Vuoristo

1 December 2020 in Surface and Coatings Technology
Verified
Journal Article
Open access
VDValentina Donadei
Valentina Donadei
Heli KoivuluotoHeli Koivuluoto
Heli Koivuluoto
ESEssi Sarlin
Essi Sarlin
Petri VuoristoPetri Vuoristo
Petri Vuoristo