Pierre-Marie Coulon

Dr. Pierre-Marie Coulon

Tyndall National Institute
+1
orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 December 2019 in Microsystems & Nanoengineering
Verified
Journal Article
Open access
PDF file
PCPierre-Marie Coulon
Pierre-Marie Coulon
BDBenjamin Damilano
Benjamin Damilano
BABlandine Alloing
Blandine Alloing
PCPierre Chausse
Pierre Chausse
SWSebastian Walde
Sebastian Walde
PSPhilip A. Shields
Philip A. Shields
Nano-engineering III-nitride semiconductors offers a route to further control the optoelectronic properties, enabling novel functionalities and applications. Although a variety of lithography techniques are currently employed to nano-engineer these materials, the scalability and cost of the fabrication process can be an obstacle for large-scale manufacturing. In this paper, we report on the use of a fast, robust and flexible emerging patterning technique called Displacement Talbot lithography (DTL), to successfully nano-engineer III-nitride materials. DTL, along with its novel and unique combination with a lateral planar displacement (D2TL), allow the fabrication of a variety of periodic nanopatterns with a broad range of filling factors such as nanoholes, nanodots, nanorings and nanolines; all these features being achievable from one single mask. To illustrate the enormous possibilities opened by DTL/D2TL, dielectric and metal masks with a number of nanopatterns have been generated, allowing for the selective area growth of InGaN/GaN core-shell nanorods, the top-down plasma etching of III-nitride nanostructures, the top-down sublimation of GaN nanostructures, the hybrid top-down/bottom-up growth of AlN nanorods and GaN nanotubes, and the fabrication of nanopatterned sapphire substrates for AlN growth. Compared with their planar counterparts, these 3D nanostructures enable the reduction or filtering of structural defects and/or the enhancement of the light extraction, therefore improving the efficiency of the final device. These results, achieved on a wafer scale via DTL and upscalable to larger surfaces, have the potential to unlock the manufacturing of nano-engineered III-nitride materials.

6 September 2018 in ACS Applied Materials & Interfaces
Verified
Journal Article
Open access
PCPierre-Marie Coulon
Pierre-Marie Coulon
GKGunnar Kusch
Gunnar Kusch
Robert MartinRobert Martin
Robert Martin
PSPhilip Shields
Philip Shields
Three-dimensional core–shell nanostructures could resolve key problems existing in conventional planar deep UV light-emitting diode (LED) technology due to their high structural quality, high-quality nonpolar growth leading to a reduced quantum-confined Stark effect and their ability to improve light extraction. Currently, a major hurdle to their implementation in UV LEDs is the difficulty of growing such nanostructures from AlxGa1–xN materials with a bottom-up approach. In this paper, we report the successful fabrication of an AlN/AlxGa1–xN/AlN core–shell structure using an original hybrid top-down/bottom-up approach, thus representing a breakthrough in applying core–shell architecture to deep UV emission. Various AlN/AlxGa1–xN/AlN core–shell structures were grown on optimized AlN nanorod arrays. These were created using displacement Talbot lithography (DTL), a two-step dry-wet etching process, and optimized AlN metal organic vapor phase epitaxy regrowth conditions to achieve the facet recovery of straight and smooth AlN nonpolar facets, a necessary requirement for subsequent growth. Cathodoluminescence hyperspectral imaging of the emission characteristics revealed that 229 nm deep UV emission was achieved from the highly uniform array of core–shell AlN/AlxGa1–xN/AlN structures, which represents the shortest wavelength achieved so far with a core–shell architecture. This hybrid top-down/bottom-up approach represents a major advance for the fabrication of deep UV LEDs based on core–shell nanostructures.

23 September 2021 in Progress in Photovoltaics: Research and Applications
Verified
Journal Article
Open access
PDF file
LSLarkin Sayre
Larkin Sayre
EAEduardo Camarillo Abad
Eduardo Camarillo Abad
PPPhoebe Pearce
Phoebe Pearce
PCPierre Chausse
Pierre Chausse
PCPierre-Marie Coulon
Pierre-Marie Coulon
LHLouise C. Hirst
Louise C. Hirst
Ultra‐thin photovoltaics enable lightweight flexible form factors, suitable for emerging terrestrial applications such as electric vehicle integration. These devices also exhibit intrinsic radiation tolerance and increased specific power and so are uniquely enabling for space power applications, offering longer missions in hostile environments and reduced launch costs. In this work, a GaAs solar cell with an 80‐nm absorber is developed with short circuit current exceeding the single pass limit. Integrated light management is employed to compensate for increased photon transmission inherent to ultra‐thin absorbers, and efficiency enhancement of 68% over a planar on‐wafer equivalent is demonstrated. This is achieved using a wafer‐scale technique, displacement Talbot lithography, to fabricate a rear surface nanophotonic grating. Optical simulations definitively confirm Fabry‐Perot and waveguide mode contributions to the observed increase in absorption and also demonstrate a pathway to short circuit current of 26 mA/cm2, well in excess of the double pass limit.

31 October 2017 in Optics Express
Verified
Journal Article
Open access
PDF file
PCPierre-Marie Coulon
Pierre-Marie Coulon
JPJ. R. Pugh
J. R. Pugh
MAM. Athanasiou
M. Athanasiou
GKG. Kusch
G. Kusch
EBE. D. Le Boulbar
E. D. Le Boulbar
PSP. A. Shields
P. A. Shields
Microcavities based on group-III nitride material offer a notable platform for the investigation of light-matter interactions as well as the development of devices such as high efficiency light emitting diodes (LEDs) and low-threshold nanolasers. Disk or tube geometries in particular are attractive for low-threshold lasing applications due to their ability to support high finesse whispering gallery modes (WGMs) and small modal volumes. In this article we present the fabrication of homogenous and dense arrays of axial InGaN/GaN nanotubes via a combination of displacement Talbot lithography (DTL) for patterning and inductively coupled plasma top-down dry-etching. Optical characterization highlights the homogeneous emission from nanotube structures. Power-dependent continuous excitation reveals a non-uniform light distribution within a single nanotube, with vertical confinement between the bottom and top facets, and radial confinement within the active region. Finite-difference time-domain simulations, taking into account the particular shape of the outer diameter, indicate that the cavity mode of a single nanotube has a mixed WGM-vertical Fabry-Perot mode (FPM) nature. Additional simulations demonstrate that the improvement of the shape symmetry and dimensions primarily influence the Q-factor of the WGMs whereas the position of the active region impacts the coupling efficiency with one or a family of vertical FPMs. These results show that regular arrays of axial InGaN/GaN nanotubes can be achieved via a low-cost, fast and large-scale process based on DTL and top-down etching. These techniques open a new perspective for cost effective fabrication of nano-LED and nano-laser structures along with bio-chemical sensing applications.

30 November 2017 in Physica Status Solidi (b)
Verified
Journal Article
Closed access
PDF file
PCPierre-Marie Coulon
Pierre-Marie Coulon
GKGunnar Kusch
Gunnar Kusch
EBEmmanuel D. Le Boulbar
Emmanuel D. Le Boulbar
PCPierre Chausse
Pierre Chausse
CBChristopher Bryce
Christopher Bryce
PSPhilip A. Shields
Philip A. Shields

5 July 2018 in Materials
Verified
Journal Article
Open access
PDF file
PCPierre-Marie Coulon
Pierre-Marie Coulon
GKGunnar Kusch
Gunnar Kusch
PFPhilip Fletcher
Philip Fletcher
PCPierre Chausse
Pierre Chausse
Robert MartinRobert Martin
Robert Martin
PSPhilip Shields
Philip Shields
As a route to the formation of regular arrays of AlN nanorods, in contrast to other III-V materials, the use of selective area growth via metal organic vapor phase epitaxy (MOVPE) has so far not been successful. Therefore, in this work we report the fabrication of a highly uniform and ordered AlN nanorod scaffold using an alternative hybrid top-down etching and bottom-up regrowth approach. The nanorods are created across a full 2-inch AlN template by combining Displacement Talbot Lithography and lift-off to create a Ni nanodot mask, followed by chlorine-based dry etching. Additional KOH-based wet etching is used to tune the morphology and the diameter of the nanorods. The resulting smooth and straight morphology of the nanorods after the two-step dry-wet etching process is used as a template to recover the AlN facets of the nanorods via MOVPE regrowth. The facet recovery is performed for various growth times to investigate the growth mechanism and the change in morphology of the AlN nanorods. Structural characterization highlights, first, an efficient dislocation filtering resulting from the ~130 nm diameter nanorods achieved after the two-step dry-wet etching process, and second, a dislocation bending induced by the AlN facet regrowth. A strong AlN near band edge emission is observed from the nanorods both before and after regrowth. The achievement of a highly uniform and organized faceted AlN nanorod scaffold having smooth and straight non-polar facets and improved structural and optical quality is a major stepping stone toward the fabrication of deep UV core-shell-based AlN or AlxGa1-xN templates.