With the advent of Industry 4.0, the manufacturing industry is facing unprecedented data challenges. Sensors, PLCs, and various types of automation equipment in smart factories continue to generate massive amounts of heterogeneous data, but existing systems generally have bottlenecks in data collection standardization, real-time processing capabilities, and system scalability, which make it difficult to meet the needs of efficient collaboration and dynamic decision making. This study proposes a multi-level industrial data processing framework based on edge computing that aims to improve the response speed and processing ability of manufacturing sites to data and to realize real-time decision making and lean management of intelligent manufacturing. At the edge layer, the OPC UA (OPC Unified Architecture) protocol is used to realize the standardized collection of heterogeneous equipment data, and a lightweight edge-computing algorithm is designed to complete the analysis and processing of data so as to realize a visualization of the manufacturing process and the inventory in a production workshop. In the storage layer, Apache Kafka is used to implement efficient data stream processing and improve the throughput and scalability of the system. The test results show that compared with the traditional workshop, the framework has excellent performance in improving the system throughput capacity and real-time response speed, can effectively support production process judgment and status analysis on the edge side, and can realize the real-time monitoring and management of the entire manufacturing workshop. This research provides a practical solution for the industrial data management system, not only helping enterprises improve the transparency level of manufacturing sites and the efficiency of resource scheduling but also providing a practical basis for further research on industrial data processing under the “edge-cloud collaboration” architecture in the academic community.

Due to their self-adaptability, low friction, low loss, and high-speed stability, bump foil aerodynamic journal bearings are widely used in high-speed rotating equipment such as turbomachinery and flywheel energy storage. In the process of high-speed operation, the heat generated leads to changes in air parameters (such as viscosity, density, etc.), thus affecting the overall performance of air bearings. In this paper, combined with the compressible Reynolds equation, a fluid–solid coupling model was established to analyze the steady-state characteristics and key influencing factors of bearings. Through the energy equation, the air viscosity–temperature effect was considered, and different boundary conditions were set. The internal temperature distribution of the air bearing and the influence of the temperature on the bearing characteristics were systematically analyzed. It was found that the bearing capacity increased when the temperature was considered. In a certain range, with the increase in ambient temperature, the increase in bearing capacity is reduced. This paper provides a theoretical design basis for the design of high-stability bearings and promotes the design of next-generation air bearings with higher speed, lower loss, and stronger adaptability, which has very important theoretical and engineering significance.

Traditional passive hydraulic dampers face the challenges of extended design cycles, inefficient parameter matching, and fixed performance, limiting their adaptability. This paper proposes an integrated solution that combines inverse parametric design with active, continuously adjustable damping. First, a high-fidelity nonlinear model is developed based on valve plate elasticity and multi-valve coupling dynamics, achieving a simulation error of ≤4%. An improved genetic algorithm is then designed to inversely optimize five key parameters. This optimization reduces the deviation between the prototype’s damping force–velocity characteristics and the target curve to ≤3% and shortens the design cycle by approximately 40%. Building on this foundation, a pilot-operated electro-hydraulic proportional relief valve is integrated to enable continuous damping adjustment. Co-simulation using AMESim2404 and MatlabSimulinkR2022 reveals the influence of solenoid valve parameters on damping characteristics and calibrates the current–damping force mapping. A co-simulation of a skyhook-controlled quarter-vehicle model demonstrates that the semi-active suspension system reduces the root mean square (RMS) of vertical body acceleration by 21.7%, indicating a significant theoretical improvement in ride comfort. This study establishes a complete technical pathway of “modeling → inverse optimization → integration → verification,” providing an efficient and viable core component solution for intelligent suspension systems.

The failure of the plug valve seal may result in dangerous accidents in the production and transportation process of petroleum and chemical products. In the paper at hand, the operating life of the plug valve is studied in the opening–closing process. The adhesion wear between the sealing surface of the plug valve is numerically studied in micro-scale, and the contact force between the sealing surface is balanced with the internal flow field of the plug valve and the deformation force between the set screw and the spool. The internal flow field of the plug valve in opening–closing process is calculated by finite element method. The deformation coupling model between the set screw and the spool is built to analyze the structure and the mechanics of the plug valve. Then, a leakage identification algorithm based on auto-correlation function is implemented for analyzing contact stress of the plug valve's sealing surfaces after wear. Finally, taking plug valve F-2 ISO-STANDARD as an example, the force of turbulent flow field on the spool is calculated during the closing process. Results show, that while the maximum contact stress increases, the pressure decreases, and the displacement trajectory of spool increases. The operating life decreases by increasing the roughness of the spool sealing surface. The model proposed provides a new practical method to evaluate the operating life of the plug valve, which is a good guidance for the design of the valve.