The employment of compounds obtained from natural sources to produce adsorbents and their application in the elimination of antibiotics from industrial effluents have gained significant attention because of their low production cost and sustainability. Herein, chitosan (biopolymer) and smectite (abundant clay mineral) were used for the low-cost and eco-friendly synthesis of a new type of adsorbent. A low-energy-consumption hydrothermal process was applied to the synthesis of the chitosan-derived carbon–smectite nanocomposite with cobalt (H_Co/C-S). The produced nanocomposite was characterized using elemental analysis, ICP-OES, XRPD, low-temperature N2 adsorption–desorption isotherms, FTIR analysis, and point of zero charge. H_Co/C-S (SBET = 0.73 m2 g−1, d001 = 1.40 nm, pHPZC = 5.3) was evaluated as a ciprofloxacin adsorbent in aqueous solution. Experimental data were fitted with different kinetic models and interpreted by selected adsorption isotherms. The pseudo-second-order model was found to be the most appropriate, while ciprofloxacin adsorption onto H_Co/C-S was best described by the Redlich–Peterson isotherm (R2 = 0.985). The maximum adsorption capacity of H_Co/C-S, according to the Langmuir isotherm (R2 = 0.977), was 72.3 mg g−1. Desorption and thermodynamic studies were performed. The obtained results indicated that the new hierarchically designed H_Co/C-S has promising potential to be further tested for application in real wastewater treatment.
1 January 2017 in Journal of the Serbian Chemical Society
Bentonites from three different deposits (Wyoming, TX, USA and Bogovina, Serbia) with similar cation exchange capacities were sodium enriched and tested as adsorbents for Sr2+ in aqueous solutions. X-Ray diffraction analysis confirmed successful Na-exchange. The textural properties of the bentonite samples were determined using low-temperature the nitrogen physisorption method. Significant differences in the textural properties between the different sodium enriched bentonites were found. Adsorption was investigated with respect to adsorbent dosage, pH, contact time and the initial concentration of Sr2+. The adsorption capacity increased with pH. In the pH range from 4.0?8.5, the amount of adsorbed Sr2+ was almost constant but 2?3 times smaller than at pH ?11. Further experiments were performed at the unadjusted pH since extreme alkaline conditions are environmentally hostile and inapplicable in real systems. The adsorption capacity of all the investigated adsorbents toward Sr2+ was similar under the investigated conditions, regardless of significant differences in the specific surface areas. It was shown and confirmed by the Dubinin?Radushkevich model that the cation exchange mechanism was the dominant mechanism of Sr2+ adsorption. Their developed microporous structures contributed to the Sr2+ adsorption process. The adsorption kinetics obeyed the pseudo-second-order model. The isotherm data were best fitted with the Langmuir isotherm model.
Catalytic degradation of tartrazine in the presence of Oxone? activated by a catalyst constituted of cobalt supported on a nanocomposite of smectite with chitosan-derived carbon was investigated. The catalyst was synthesized using cobalt impregnation followed by carbonization at 773 K in an inert atmosphere. The synthesized catalyst was previously fully characterized using appropriate characterization methods, including XRPD, XPS, FTIR, HRTEM, and low-temperature N2-physisorption analysis. The catalytic experiments were performed by varying different experimental parameters (dye concentration, Oxone? concentration, temperature, and initial pH of the reaction solution). The kinetic and thermodynamic parameters were estimated from the experimental results. The kinetics data showed the best fit with the pseudo-first-order kinetics model. The activation energy of the investigated degradation process was calculated according to the Arrhenius equation. The catalyst showed excellent performance at low temperatures even at 298 K, and in the wide range of pH values.
Dry Turkish oak (Quercus cerris) sawdust, untreated and treated with three activators, (H3PO4, NaOH and H2O2) was pyrolyzed under limited-oxygen conditions to obtain biochar samples. The electrochemical properties of these samples were tested and compared to the properties of several commercial carbon blacks. The electrochemical characterization was performed via cyclic voltammetry, analyzing the response toward two commonly used redox probes, [Fe(CN)6]3−/−4− and [Ru(NH3)6]2+/3+. The influence of the scan rate on this response was investigated, and the resulting data were used to obtain the values of the heterogenous charge transfer constant, k0. Higher k0 values were observed for carbon blacks than for investigated biochar samples. The detection of 4-nitrophenol and heavy metal ions was used to assess the applicability of biochars for electroanalytical purposes. The response of untreated biochar was comparable with the response of Vulcan carbon black, which showed the best response of all analyzed carbon blacks.
Bentonite from Mecji Do locality in Serbia was modified with hexadecyltrimethylammonium bromide (HDTMA-Br), and the sample was denoted as HDTMA-MD. The characterization of the material included X-Ray diffraction, elemental analysis and point of zero charge determination. The adsorption of phenol and its nitro derivatives: 2-nitrophenol (2NP), 3-nitrophenol (3NP) and 4-nitrophenol (4NP) on HDTMA-MD was investigated. The adsorption capacity of HDTMA-MD toward phenol derivatives increased in the following order qe (phenol) < qe (3NP) < qe (2NP) < qe (4NP). The influence of adsorption time and initial concentration on the adsorption efficiency of HDTMA-MD was studied for 4NP. The data were best fitted with Langmuir isotherm model and the pseudo-second-order kinetic model.