This study mainly investigated the adsorption behavior and mechanism of microfiltration membranes (MFMs) with different physiochemical properties (polyamide (PA), polyvinylidene fluoride (PVDF), nitrocellulose (NC), and polytetrafluoroethylene (PTFE)) for bisphenol A (BPA). According to the adsorption isotherm and kinetic, the maximum adsorption capacity of these MFMs was PA (161.29 mg/g) > PVDF (80.00 mg/g) > NC (18.02 mg/g) > PTFE (1.56 mg/g), and the adsorption rate was PVDF (K1 = 2.373 h−1) > PA (K1 = 1.739 h−1) > NC (K1 = 1.086 h−1). The site energy distribution analysis showed that PA MFMs had the greatest adsorption sites, followed by PVDF and NC MFMs. The study of the adsorption mechanism suggested that the hydrophilic microdomain and hydrophobic microdomain had a micro-separation for PA and PVDF, which resulted in a higher adsorption capacity of PA and PVDF MFMs. The hydrophilic microdomain providing hydrogen bonding sites and the hydrophobic microdomain providing hydrophobic interaction, play a synergetic role in improving the BPA adsorption. Due to the hydrogen bonding force being greater than the hydrophobic force, more hydrogen bonding sites on the hydrophobic surface resulted in a higher adsorption capacity, but the hydrophobic interaction contributed to improving the adsorption rate. Therefore, the distribution of the hydrophilic microdomain and hydrophobic microdomain on MFMs can influence the adsorption capacity and the adsorption rate for BPA or its analogues. These consequences provide a novel insight for better understanding the adsorption behavior and mechanism on MFMs.
Considering the notable mechanical properties of thermoplastic polyurethane (TPU), polydopamine–polyethyleneimine (PEI) -modified TPU nanofiber membranes (PDA/PEI-TPU NFMs) have been developed successfully for removal of anionic azo dyes. The adsorption capacity of PDA/PEI-TPU NFMs was evaluated using three anionic dyes: congo red (CR), sunset yellow (SY), and methyl orange (MO). Interestingly, it exhibited different adsorption behaviors and mechanisms of CR on PDA/PEI-TPU NFMs compared with SY and MO. With the decrease in pH, leading to more positive charges on the PDA/PEI-TPU NFMs, the adsorption capacity of SY and MO increased, indicating electrostatic interaction as a main mechanism for SY and MO adsorption. However, wide pH range adaptability and superior adsorption have been observed during the CR adsorption process compared to SY and MO, suggesting a synergistic effect of hydrogen bonding and electrostatic interaction, likely as a critical factor. The adsorption kinetics revealed that chemical interactions predominate in the CR adsorption process, and multiple stages control the adsorption process at the same time. According to the Langmuir model, the maximum adsorption capacity of CR, SY and MO were reached 263, 17 and 23 mg/g, respectively. After six iterations of adsorption–desorption, the adsorption performance of the PDA/PEI-TPU NFMs did not decrease significantly, which indicated that the PDA/PEI-TPU NFMs have a potential application for the removal of CR molecules by adsorption from wastewater.
Dye wastewater containing bisphenol A (BPA) and dyes as pollutants has not been adequately studied. Our previous study revealed that thermoplastic polyurethane (TPU) nanofiber membranes (NFMs) modified by the addition of polyethyleneimine (PEI) and polydopamine (PDA) satisfactorily adsorb dyes. Herein, we first optimized the synthesis conditions for such membranes, noting a PEI/PDA monomer ratio of 2:2 and a deposition time of 48 h to be optimal. Experiments using these membranes revealed that binary systems containing BPA and the dyes (Congo red (CR), Eosin yellow (EY), or sunset yellow (SY)) exhibit three adsorption behaviors. CR and BPA compete with each other for adsorption sites, decreasing the maximum adsorption capacity (Qmax) for CR 208.3 mg/g (in a monomeric system) to 182.4 mg/g. The adsorption rates for CR and BPA decreased from 0.002 min−1 and 0.331 min−1 in the monomeric systems to 8.37 × 10−4 min−1 and 0.072 min−1, respectively, in the binary CR–BPA system, exhibiting antagonistic effects. When EY and BPA coexisted, Qmax for EY increased from 60.0 (monomeric) to 71.9 mg/g, whereas that for BPA increased from 35.6 to 43.2 mg/g, showing a synergistic effect due to the possible bridging effect. The adsorption sites for SY and BPA are independent of each other. The novelty of this study is the finding that PDA/PEI-TPU NFMS exhibited high adsorption capacity for dyes and BPA in binary composite systems and PDA/PEI-TPU NFMs showed different adsorption patterns for three dye–BPA binary composite systems. The preparation of PDA/PEI-TPU NFMs and the investigation of the adsorption mechanism for dye–BPA binary composite systems are not only of theoretical importance but also provide experimental and data support for practical applications.
As a special zone of periodic impoundment and flooding in the Three Gorges Reservoir (TGR), the water-level fluctuation zone (WLFZ) of TGR acts as a short-term ‘sink’ for hydrophobic endocrine disrupting compounds (EDCs). This study was conducted on the adsorption/desorption kinetics and equilibriums of four target EDCs (i.e., estrone (E1), 17β-estradiol (E2), 17α-ethynylestradiol (EE2), and bisphenol A (BPA)) in soil samples (i.e., S1, S2, S3, and S4), which were collected from different elevation gradients of the WLFZ at Qingxi Town of Fulin in TGR. Under the influence of the water-level fluctuation, S1 and S2 from the frequent inundation area had smaller particle sizes with more organic matter (OM) and total nitrogen (TN) content, whereas soils S3 and S4 from the long-term exposed area had a higher fraction of sand with lower OM and TN. All four target EDCs could achieve an adsorption equilibrium within 24 h, and the kinetics of the adsorption/desorption fitted the pseudo-second-order model excellently. The adsorption/desorption isotherms of the EDCs were better described by the Freundlich equation. The adsorption capacity decreased, as 17α-ethynylestradiol (EE2) > 17β-estradiol (E2) > estrone (E1) > bisphenol A (BPA), in each tested soil. S1 and S2 exhibited a greater capacity but a lower degree of nonlinearity to adsorb the target EDCs than S3 and S4. The values of the Gibbs free energy suggested that the EDCs adsorption in the tested soils was dominated by unstable physical adsorption. The desorption hysteresis of E1, E2, and EE2 were stronger in S1 and S2, whereas the BPA exhibited weak or almost no hysteresis in all of the tested soils. The substantial water-level fluctuation imposed on the TGR would have a continuous influence on the EDCs adsorption/desorption by altering the soil properties. Thus, long-term monitoring and further research of EDCs in this region are urgent.
Dye wastewater containing bisphenol A (BPA) and dyes as pollutants have not been adequately studied. Our previous study revealed that thermoplastic polyurethane (TPU) nanofiber membranes (NFMs) modified by the addition of polyethyleneimine (PEI) and polydopamine (PDA) satisfactorily adsorb dyes. Herein, we first optimized the synthesis conditions for such membranes, noting a PEI:PDA monomer ratio of 2:2 and a deposition time of 48 h to be optimal. Experiments using these membranes revealed that binary systems containing BPA and the dyes (Congo red (CR), Eosin yellow (EY), or sunset yellow (SY)) exhibit three adsorption behaviors. CR and BPA compete with each other for adsorption sites, decreasing the maximum adsorption capacity (Qmax) for CR 208.3 mg/g (in a monomeric system) to 182.4 mg/g, whereas for BPA, it decreased from 26.7 to 22.8 mg/g. The adsorption rates for CR and BPA decreased from 0.002 min−1 and 0.331 min−1 in the monomeric systems to 8.37 × 10−4 min−1 and 0.072 min−1, respectively, in the binary CR–BPA system, exhibiting antagonistic effects. When EY and BPA coexist, Qmax for EY increased from 60.0 (monomeric) to 71.9 mg/g, whereas that for BPA increased from 35.6 to 43.2 mg/g, showing a synergistic effect due to the possible bridging effect. The adsorption sites for SY and BPA are independent of each other. Thus, PDA/PEI TPU NFMs exhibit the potential for removal of dye–BPA composites, whereas binary systems containing BPA with different dyes are adsorbed differently.