A series of Ce-doped α-MnO2 catalysts (CeXMn1−XO2, x = 0.04, 0.07, 0.10) were synthesized by a simple in situ hydrothermal method. It was confirmed by characterization methods such as XRD, Raman, N2 adsorption–desorption and SEM confirmed that the introduction of Ce significantly regulated the microstructure of α-MnO2, specifically manifested as the reduction in grain size, the increase in defect sites, the increase in Mn-O bond length and altered morphological structure. H2-TPR, O2-TPD and XPS analyses further revealed the strong interaction between Mn and Ce, accompanied by significant electron transfer (Ce3+ + Mn4+ → Ce4+ + Mn3+), thereby promoting the formation of Mn3+ species. In the test of toluene catalytic oxidation performance, Ce0.07Mn0.93O2 exhibited the most excellent catalytic activity (T100 = 280 °C), while also having good thermal stability and water resistance. Furthermore, the degradation pathways of toluene were analyzed by TD-GC-MS technology: Toluene → Benzene → Benzaldehyde → Maleic anhydride → CO2 and H2O.
Photothermal catalysis has emerged as a promising approach for the efficient and cost-effective removal of volatile organic compounds (VOCs). Pt@MnO2 catalysts have demonstrated excellent performance in the photothermal catalytic oxidation of VOCs. However, current research has predominantly focused on the interaction between Pt and MnO2, while often overlooking the influence of the MnO2 crystal phase. Therefore, in this study, we synthesized Pt supported on four crystal phases (α, β, γ, and δ) of MnO2 and established the structure–activity relationships through performance evaluation and characterization. Among the prepared catalysts, Pt@Mn[δ] exhibited excellent performance and possessed outstanding stability. Crystal structure characterization revealed that the larger specific surface area and lower crystallinity of Pt@Mn[δ] exposed more active sites. XPS analysis indicated the transformation of Mn4+ to Mn3+ on Pt@Mn[δ], leading to the formation of oxygen vacancies. O2-TPD and H2-TPR further confirmed the activation of lattice oxygen and the promoted redox cycle of Pt@Mn[δ]. UV-Vis DRS and electrochemical measurements demonstrated that Pt@Mn[δ] exhibited the most pronounced visible-light absorption, the highest photocurrent density, the lowest charge transfer resistance and superior charge carrier mobility. TD-GC-MS analysis indicated that o-xylene underwent alkylation and isomerization, with subsequent oxidation following the Mars–van Krevelen (MvK) mechanism.
Selective CO2 hydrogenation over Ni-based catalysts requires control of the competing reverse water–gas shift (RWGS) and methanation pathways. Here, γ-Al2O3-supported Ni catalysts with nominal loadings of 5, 10, 15 and 20 wt% were prepared by wet impregnation. Structural, textural, reduction and surface analyses showed that Ni loading altered NiO crystallinity, pore accessibility, reducibility and the fitted surface Ni-state distribution. The 10%Ni/γ-Al2O3 catalyst reached 55% CO2 conversion, approximately 90% CO selectivity and a CO production rate of 147.2 mmol CO·gcat−1·h−1 at 600 °C. Increasing the H2/CO2 ratio from 1 to 4 at 500 °C raised conversion from 46% to 65% but decreased CO selectivity from 88% to 76%. The catalyst also maintained a nearly constant response during a 24 h time-on-stream test at 500 °C. In situ DRIFTS detected bicarbonate-, formate- and adsorbed-CO-related species, consistent with the participation of oxygenated intermediates in RWGS. Together, these results establish an internally controlled loading–structure–performance relationship and identify 10%Ni/γ-Al2O3 as providing the most favorable conversion–selectivity–productivity balance within the investigated series.
The development of highly efficient catalysts is important for the photothermal catalytic oxidation of volatile organic compounds (VOCs). Herein, MIL-100(Fe) was used as the sacrificial template to prepare MnFeOx catalysts with different Mn contents through the impregnation–calcination method, and their performance in photothermal catalytic oxidation of toluene was investigated. The results show that the content of Mn significantly affects the crystal phase structure, pore properties, surface chemical state, and optical response of the catalyst. Among them, 30%MnFeOx exhibits the best photothermal catalytic activity, with T50 and T90 being 211 and 237 °C, respectively, which are significantly lower than those of FeOx (232 and 260 °C). Characterization results suggested that the introduction of Mn caused the bandgap of FeOx to decrease from 1.96 to 1.67 eV. Meanwhile, the surface Fe2+, adsorbed oxygen (Oads) species, and oxygen vacancies were increased, enhancing visible light absorption and gaseous oxygen species adsorption and activation, which promoted the photothermal catalytic oxidation of toluene. Additionally, the 30%MnFeOx catalyst presented good thermal stability and water resistance. Furthermore, during the reaction process, the in situ activation of the catalyst’s surface induced the increase in surface Fe2+, Mn3+, and Oads species, which enhances the photothermal catalytic activity of the catalyst. Importantly, the in situ DRIFTS results further indicate that toluene is mainly oxidized along the path of toluene → benzyl alcohol → benzoate → maleic anhydride → CO2 and H2O. This work provides a theoretical basis for the construction of low-cost, non-precious-metal Mn–Fe-based photothermal catalysts.