Wisam Hamdan

Wisam Hamdan


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2023 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
PDF file
WHWisam Hamdan
Wisam Hamdan
SASaad Mahmood Ali
Saad Mahmood Ali
ZSZaid Hayder Saleh
Zaid Hayder Saleh
DADalia Mohammed Awad
Dalia Mohammed Awad
FTFeryal Zeyad Tareq
Feryal Zeyad Tareq
TRTuqa Mohammed Radi
Tuqa Mohammed Radi
Diseases of the human musculoskeletal system are increasingly common, especially those affecting the knee joint, for various reasons, including those that resul

1 January 2024 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
PDF file
NGNoor A. Ghassan
Noor A. Ghassan
WHWisam Hamdan
Wisam Hamdan
Flatfoot is a joint foot abnormality in which the foot arch collapse from either childhood or adulthood. Flatfoot can be caused by tarsal coalition, accessory n Flatfoot is a joint foot abnormality in which the foot arch collapse from either childhood or adulthood. Flatfoot can be caused by tarsal coalition, accessory n

30 April 2026 in Management Systems in Production Engineering
Verified
Journal Article
Open access
PDF file
STShahd Taqi
Shahd Taqi
SSSaad kareem Shather
Saad kareem Shather
WHWisam Hamdan
Wisam Hamdan
The development of modern industries necessitates complexity and the creation of manufactured models to keep pace with advancements. Magnetic abrasive finishing (MAF) is the most prominent finishing technique due to its effectiveness and efficiency without damaging the part. This study fills a research gap by directly comparing dry and lubricated magnetic abrasive finishing (MAF) using hybrid abrasive particles on geometrically complex surfaces, with surface quality evaluated through non-contact laser scanning and SEM. This work investigates the effect of adding lubricating oil to the abrasive grain finishing technique, comparing this finishing with traditional dry finishing. The magnetic abrasive grains used were prepared from a hybrid mixture consisting of two types of abrasive particles: silicon carbide (SiC) and tungsten carbide (WC), with the addition of iron particles to enhance the magnetic attraction force. The tool was magnetized with a permanent neodymium magnet. Three operational variables were controlled at three levels: feed rate, tool rotation speed, and particle size. The surface roughness of the samples was measured before and after the finishing process to assess the improvement. Since the designs of the samples used for the experiments were non-planar, they were difficult to inspect using conventional techniques. Therefore, laser scanning technology, in addition to scanning electron microscopy, was used to assess surface defects. Experimental results showed that the oillubricated finishing process performed better than the dry finishing process, with the oil-lubricated finishing process achieving an improvement of approximately 66.4% compared to the dry finishing process, which achieved a 36.9% improvement under the same operating conditions. The experimental results demonstrated that the level of influence of these variables on finishing performance may vary depending on the external operating conditions.

28 October 2025 in Nano Hybrids and Composites
Verified
Journal Article
Closed access
PDF file
RKReem S. Khzaall
Reem S. Khzaall
WHWisam Hamdan
Wisam Hamdan
Marwan ArbileiMarwan Arbilei
Marwan Arbilei
Polylactic acid (PLA) has become a promising material for medical implants due to its biocompatibility, biodegradability, and favorable mechanical properties. With advancements in Fused Deposition Modeling (FDM) 3D printing technology, it is possible to further optimize the performance of PLA by adjusting printing parameters. This optimization is crucial for enhancing the energy absorption and durability of PLA, especially in applications like medical implants that require reliable mechanical strength. This study utilized Response Surface Methodology (RSM) with the Box-Behnken Design (BBD) to investigate the effects of key FDM 3D printing parameters—layer thickness, infill pattern, and infill density—on the energy absorption and durability of PLA. A total of 15 experiments were conducted, with each factor tested at three levels. The standard Charpy impact test (ISO 179) was used to measure energy absorption in samples of dimensions 80x10x4 mm. This research aims to identify the key FDM 3D printing parameters that maximize the energy absorption and durability of polylactic acid (PLA) for use in medical implants, leveraging PLA's biocompatibility and mechanical properties. The study found that infill density and infill pattern are the two most critical factors affecting the energy absorption and durability of PLA. An infill density of 80% was determined to be optimal, as higher densities significantly improved energy absorption. Additionally, the grid infill pattern, combined with the highest layer thickness of 0.3 mm, provided the best performance. In conclusion, these findings offer valuable insights for optimizing PLA in medical implant applications, with potential for further refinement based on specific use cases.

1 January 2024 in Salud, Ciencia y Tecnología - Serie de Conferencias
Verified
Journal Article
Open access
PDF file
NGNoor A. Ghassan
Noor A. Ghassan
WHWisam Hamdan
Wisam Hamdan
Flatfoot is an abnormality that affects forefoot, midfoot, and hindfoot. This deformity also referred to as pes planus, in which the medial longitudinal arch is collapsed. Flatfoot can be accosted with symptoms such as pain and swelling. Objective: the aim of this study is to develop an adaptable flatfoot orthosis that uses an airbag cushion to support the arch and help in reducing the pain and improving the pressure distribution. Methods: the patient went through a physical test and a cast from Plaster bandage was made to the patient’s foot to have the exact foot measurement for the orthosis design. The orthosis was made from two layers, the first layer was made from a Polypropylene sheet as the orthosis base, and the second layer was made from Plastazote. The airbag cushion was placed between the two layers and connected to the air pump. Gait analysis test was carried out on PWALK device with two conditions (with foot orthosis, and without foot orthosis) to test the efficiency of the orthosis. Results: the gait analysis confirmed that foot orthotics optimize pressure distribution, arch height, and pain reduction during the gait cycle. Conclusion: our study aims to analyze the benefits of using airbag cushions in flatfoot orthosis. We designed a prototype orthosis with a semi-rigid structure and an airbag cushion to support the arch. The semi-rigid structure allows for normal foot arch mobility, while the airbag cushion helps reduce pain and improve arch height and pressure distribution