This study investigates the corrosion and scaling behaviour of Extreme High-speed Laser Application (EHLA)-fabricated corrosion-resistant alloy (CRA) claddings under simulated geothermal brine conditions. EHLA 316L stainless steel and alloy 625 coatings were produced and tested in simulated brine (chloride–carbonate–silica geothermal brine) at 70 °C for 720 h to evaluate the influence of additive manufacturing (AM) microstructures on corrosion performance. The EHLA coatings exhibited dense, metallurgically bonded microstructures with minimal porosity. Microstructural analysis revealed Nb- and Mo-rich segregation in EHLA 625 and fine columnar dendritic morphology in all coatings. EHLA 625 developed a stable passive film with only a thin deposit of Mg-O-containing compounds, whereas EHLA 316L exhibited localised pitting and significant Si- and Mg-containing scale accumulation, especially in as-built conditions. Surface finishing reduced corrosion activity by minimising roughness and defect-driven localised attack. Critical pitting temperature (CPT) tests confirmed the superior localised corrosion resistance of EHLA 625 relative to EHLA 316L under laboratory conditions. While these results indicate promising corrosion and scaling resistance of EHLA coatings, further process optimisation and post-deposition thermal treatments might be required to achieve coating performance comparable to wrought alloys. The results indicate the potential of EHLA-fabricated coatings for producing corrosion and scaling resistance surfaces.

This study investigates the corrosion and scaling behaviour of Extreme High-speed Laser Application (EHLA)-fabricated corrosion-resistant alloy (CRA) claddings under simulated geothermal brine conditions. EHLA 316L stainless steel and alloy 625 coat-ings were produced and tested in simulated brine (Chloride–carbonate–silica geo-thermal brine) at 70°C for 720h to evaluate the influence of additive manufacturing microstructures on corrosion performance. The EHLA coatings exhibited dense, met-allurgically bonded microstructures with minimal porosity. Microstructural analysis revealed Nb- and Mo- rich segregation in EHLA 625 and fine columnar dendritic morphology in all coatings. EHLA 625 also displayed stable passive film formation but had a thin deposit of Mg-O-containing compounds from the brine. EHLA 316L on the other hand exhibited localised pitting and heavy Si- and Mg-containing scale accumu-lation, especially in as-built conditions. Surface finishing reduced corrosion activity by minimizing roughness and defect-driven localised attack. Critical pitting temperature tests confirmed the superior localised corrosion resistance of EHLA 625 compared to EHLA 316L. However, further process improvements and perhaps post-deposition thermal treatments might be required to bring the performance of the coatings in line with the wrought alloys. The results demonstrate that EHLA-fabricated coatings offer corrosion and scaling resistance. This coating technique has the potential to provide cost-effective solutions to produce corrosion resistant coatings on geothermal components.

Currently, there are several deep drill geothermal projects that aim to discharge superheated or supercritical geothermal fluid for sustainable power production. In geothermal power utilisation, the well casing steel and surface equipment is susceptible to corrosion due to corrosive species in the geothermal fluid. The temperature and the phase state of the fluid greatly affect the extent and the forms of corrosion that can occur. To mitigate corrosion damage in the casing and surface equipment, the recently developed production method Extra High-speed Laser Application (EHLA) cladding is proposed as a solution. To simulate application of carbon steel and EHLA clads in superheated geothermal wells, the materials were tested in a superheated steam containing CO₂ and H₂S at 450 °C temperature and 150 barG pressure. Microstructural and chemical analysis was performed with SEM, EDX and XRD, and corrosion rate was analysed with the weight loss method. The carbon steel was prone to corrosion with a double corrosion layer but the corrosion of the EHLA clads was insignificant. The results show that the EHLA clads tested have good corrosion resistance in the test environment, and the study can aid in the selection of casing and clad materials for future deep geothermal wells. Furthermore, this study shows that the EHLA clads increase the variety of corrosion mitigation solutions for future geothermal projects.

Carbon steel casing material in high-temperature deep geothermal wells can be prone to severe corrosion and premature failure due to the oxidation capacity of H₂O, H₂S, CO₂, and more corrosive species in geothermal fluid. Due to the higher temperature and pressure and phase state of fluid in high-temperature deep geothermal wells, the rate and extent of corrosion can be expected to be different than in low-temperature geothermal wells. To reduce the extent of corrosion damage and corrosion rate, and increase the lifetime of geothermal wells, one mitigation method is to clad the internal surface of the geothermal casing with a more noble, corrosion-resistant material. Conventional cladding, however, has been an expensive and time-consuming process up to the current date, but recently, a more economical and productive method has been established, i.e., EHLA cladding. In this study, a 14-day corrosion performance test was conducted on stainless steel and nickel-based alloy clads on a carbon steel substrate in a 262 °C and 95 bar geothermal well in the Hellisheidi geothermal field (SW Iceland). Samples were partially or fully cladded, and some samples were stressed to investigate the clads’ susceptibility to general corrosion and stress corrosion cracking, as well as the substrate’s vulnerability to galvanic corrosion. Corrosion analysis of pure carbon steel substrate was also investigated for comparison. Samples were microstructurally analysed with SEM, and chemical analysis was performed with EDX. The results indicated that the clad materials have good corrosion resistance in the geothermal environment tested, suggesting that EHLA cladding is a more feasible option for strengthening the corrosion resistance of geothermal casing and equipment.