Burak Özdemir

Dr. Burak Özdemir

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2019 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
EBErkan Bahçe
Erkan Bahçe
BÖBurak Özdemir
Burak Özdemir

28 December 2022 in Journal of Natural Fibers
Verified
Journal Article
Open access
BÖBurak Özdemir
Burak Özdemir
AYAHMET YARDIMEDEN
AHMET YARDIMEDEN
EBErkan Bahçe
Erkan Bahçe
EKErol Kilickap
Erol Kilickap
EEEnder Emir
Ender Emir
In the study, Natural jute composite materials, which have environmental advantages due to their easily degradable nature were drilled with different processing parameters and the effects of thrust force, vibration and temperature changes on hole quality were investigated. The effect of feed and spindle speed was statistically analyzed using ANOVA method. The thrust force, vibration and temperature factors that occur depending on the drilling parameters vary and affect the roughness and delamination values. The effect of feed and speed on thrust force was calculated as 97.87% and the feed effect (90.85%) is far greater than the speed (9.15%). The effect of drilling parameters on vibration is statistically insignificant due to the different spread behavior in the layers of the composite material (R2 = 0.2329). However, feed effect on vibration (94.6%) is greater than the speed effect (6.06%). The temperature is affected by 96.93% of the drilling parameters and the speed is 84.16% and the feed is 15.83%. The roughness effect depending on the drilling parameters is measured as 84.91%. The effect of speed on roughness (90.26%) is greater than the feed (9.73%). It has been determined that this situation is mostly related to vibration and temperature.

10 March 2023 in Materials and Manufacturing Processes
Verified
Journal Article
Closed access
BÖBurak Özdemir
Burak Özdemir
EKErol Kilickap
Erol Kilickap
EBErkan Bahçe
Erkan Bahçe
AYAHMET YARDIMEDEN
AHMET YARDIMEDEN
EEEnder Emir
Ender Emir
In the drilling process, the angle of surface is one of the parameters that affect hole quality. In study, the effects of feed rate, spindle speed and surface angle on the thrust force, roughness, and delamination, which are the factors affecting the quality of hole, were investigated in the drilling of GFRP (glass fiber reinforced polymer) and CFRP (carbon fiber reinforced polymer) with freeform surfaces. With ANOVA (Analysis of Variance) and regression analysis, the parameter effects were statistically compared, and descriptive mathematical models were derived. The mathematical models were subjected to the Genetic Algorithm approach according to the different surface angles determined and the optimum parameter values were calculated. Guiding data were obtained about the effects of machining on hole quality in drilling composite at different surface angles, which is the main motivation of the study. Optimization results will improve hole quality on curved surfaces, while saving cost and time. Graphical Abstract

3 June 2020 in International Journal of Precision Engineering and Manufacturing-Green Technology
Verified
Journal Article
Closed access
PDF file
EBErkan Bahçe
Erkan Bahçe
BÖBurak Özdemir
Burak Özdemir

11 October 2019 in IET Image Processing
Verified
Journal Article
Open access
PDF file
EBErkan Bahçe
Erkan Bahçe
BÖBurak Özdemir
Burak Özdemir
It is known that parameters such as the feed rate and the spindle speed affect the hole quality during the drilling of aluminium and its alloys. In particular, deflection occurs as a result of the increase or decrease of the reverse forces acting on the tool as a result of changing the parameter values. The tool deflection causes deviations in the hole geometry. This requires the initial detection of the deflection on the tool and then the most appropriate updating of the drilling parameters. At the present time, force‐based estimation and inductive or laser sensor detection methods are used for the detection of tool deflection. These methods are useless because they require expensive measurement systems and continuous fine‐tuning. This study aimed to calculate the tool deflection that occurs during the drilling of AL 7075 material using an image processing technique. In the experiments using different drilling parameters, the tool deflection was calculated and the effects of the parameters on tool deflection were investigated. As a result, it is shown that the tool deflection can be detected quickly and simply by image processing. In addition, the effects of the processing parameters on the tool deflection are discussed.

19 November 2022 in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
Verified
Journal Article
Closed access
BÖBurak Özdemir
Burak Özdemir
EBErkan Bahçe
Erkan Bahçe
In milling, some of the factors that contribute to the poor quality of products are the cutting forces. Depending on the machining parameters, the cutting forces may significantly affect the tool being used in the machining process. Tool deflection can be modeled as bending deformation. Tool deflection causes poor surface quality, geometrical and dimensional errors. For this reason, it must be addressed during milling and reduced by changing the machining parameters. In the determination of tool deflection, force-based analytical and finite element methods (FEM) and sensor measurement methods are widely used. These technologies have drawbacks such as not being able to obtain fast data, being expensive, demanding precise control, and requiring continual calibration. This study aims to determine the deflection of the tool by image processing dependent on the tool/material pair and machining parameters in the milling process. For this purpose, the AL7075 material with a free-form surface was machined on a CNC milling machine. A mathematical equation is proposed to estimate the tool deflection based on the image processing results. The method has shown that tool deviation can be detected more quickly and simply by image processing.