Cyclic solvent injection (CSI) with CO2 is a promising non-thermal enhanced oil recovery (EOR) method for heavy oil reservoirs that also supports CO2 sequestration. However, its effectiveness is limited by short foamy oil flow durations and low CO2 utilization. This study explores how waterflooding and nanoparticle-assisted flooding can enhance CO2-CSI performance through experimental and numerical approaches. Three sandpack experiments were conducted: (1) a baseline CO2-CSI process, (2) a waterflood-assisted CSI process, and (3) a hybrid sequence integrating CSI, waterflooding, and nanoparticle flooding. The results show that waterflooding prior to CSI increased oil recovery from 30.9% to 38.9% under high-pressure conditions and from 26.9% to 28.8% under low pressure, while also extending production duration. When normalized to the oil saturation at the start of CSI, the Effective Recovery Index (ERI) increased significantly, confirming improved per-unit recovery efficiency, while nanoparticle flooding further contributed an additional 5.9% recovery by stabilizing CO2 foam. The CO2-CSI process achieved a maximum CO2 sequestration rate of up to 5.8% per cycle, which exhibited a positive correlation with oil production. Numerical simulation achieved satisfactory history matching and captured key trends such as changes in relative permeability and gas saturation. Overall, the integrated CSI strategy achieved a total oil recovery factor of approximately 70% and improved CO2 sequestration efficiency. This work demonstrates that combining waterflooding and nanoparticle injection with CO2-CSI can enhance both oil recovery and CO2 sequestration, offering a framework for optimizing low-carbon EOR processes.
Combining multiple secondary oil recovery (SOR)/enhanced oil recovery (EOR) methods can be an effective way to maximize oil recovery from heavy oil reservoirs; however, previous studies typically focus on single methods. In order to optimize the combined process of ethane-based cyclic solvent injection (CSI) and water/nanoparticle-solution flooding, a comprehensive understanding of the impact of injection pressure, water, and nanoparticles on CSI performance is crucial. This study aims to provide such understanding through experimental evaluation, advancing the knowledge of EOR methods for heavy oil recovery. Three approaches (an ethane-based CSI process, water flooding, and nanoparticle-solution flooding) were applied through a cylindrical sandpack model with a length of 95.0 cm and a diameter of 3.8 cm. Test 1 conducted an ethane-based CSI process only. Test 2 conducted a combination approach of CSI–water flooding–CSI–nanoparticle-solution flooding–CSI. Specifically, the injection pressure of the first CSI phase in Test 2 was gradually increased from 3500 to 5500 kPa. The second and the third CSI phases had the same injection pressure as Test 1 at 5500 kPa. The CSI process ceased once the oil recovery was less than 0.5% of the original oil in place (OOIP) in a single cycle. Results show that the ethane-based CSI process is sensitive to injection pressure. A high injection pressure is crucial for optimal oil recovery. The first CSI phase in Test 2, where the injection pressure was increased gradually, resulted in a 2.9% lower oil recovery and five times as much ethane consumption compared to Test 1, which applied a high injection pressure. It was also found that water flooding improved the oil recovery in the CSI process. In Test 2, the oil recovery factor of the second CSI phase increased by 57% after the water flooding process, which is likely due to the formation of water channels and a dispersed oil phase that increased the contact area between ethane and oil. Although the nanoparticle-solution flooding only had 0.3% oil recovery, after that the third CSI phase stimulated another 10.8% of OOIP even when the water saturation achieved more than 65%. This demonstrated that the addition of nanoparticles can maintain the stability of the foam and enhance the transfer of ethane to the heavy oil. Finally, Test 2 reached a total oil recovery factor of 76.1% on a lab scale, an increase of 45% compared to the single EOR method, which proved the combination process is an efficient method to develop a heavy oil field.
20 April 2026 in Engineering Analysis with Boundary Elements