Binary Zr-Ti alloys spontaneously develop a tenacious and compact oxide layer when their fresh surface is exposed either to air or to aqueous environments. Electrochemical impedance spectroscopy (EIS) analysis of Zr-45Ti, Zr-25Ti, and Zr-5Ti exposed to simulated physiological solutions at 37 °C evidences the formation of a non-sealing bilayer oxide film that accounts for the corrosion resistance of the materials. Unfortunately, these oxide layers may undergo breakdown and stable pitting corrosion regimes at anodic potentials within the range of those experienced in the human body under stress and surgical conditions. Improved corrosion resistance has been achieved by prior treatment of these alloys using thermal oxidation in air. EIS was employed to measure the corrosion resistance of the Zr-Ti alloys in simulated physiological solutions of a wide pH range (namely 3 ≤ pH ≤ 8) at 37 °C, and the best results were obtained for the alloys pre-treated at 500 °C. The formation of the passivating oxide layers in simulated physiological solution was monitored in situ using scanning electrochemical microscopy (SECM), finding a transition from an electrochemically active surface, characteristic of the bare metal, to the heterogeneous formation of oxide layers behaving as insulating surfaces towards electron transfer reactions.
In situ electrochemical imaging of corrosion reactions is performed directly by scanning electrochemical microscopy (SECM) in generation-collection mode. This method involves redox conversion of soluble metal ions at the amperometric tip for quantification. Unfortunately, many metals, such as copper, do not undergo redox conversion to a soluble state and are deposited on the SECM tip. They therefore modify the electrochemical behavior of the tip and require consideration of metal stripping processes. In addition, the miniaturization of the electrode to operate as a microelectrode tip can be accompanied by variations in the potential range and distribution of the redox processes related to copper deposition and redissolution, thus complicating the adequate choice of electrochemical conditions applied to the tip for the unambiguous operation of SECM in the generation-collection mode to study the corrosion of copper-based materials. Therefore, in this work, a study of different parameters for the amperometric determination of Cu2+ ions was conducted using gold disk electrodes of 500 and 10 μm diameter to represent the typical sizes employed in conventional and scanning microelectrochemical measurements. The investigation was performed to analyze the effect of underpotential deposition (UPD) and overpotential deposition (ODP) on the voltammetric characteristics of copper deposition and redissolution resulting from variations in the solution composition, i.e., the nature of anions and pH. The dependence and limits of the reduction and reoxidation waves were analyzed as functions of the Cu2+ ion concentration, the ionic strength of the electrolyte, and the pH of the solution. The results were interpreted as UPD and OPD. Under conditions close to the marine environment, the release of Cu2+ ions can be unambiguously detected and quantified from potentials above −0.1 V vs. Ag/AgCl.
This work describes a simple and economical electrochemical route for the generation of mesoporous alumina (MA) particles that can serve as containers for corrosion inhibitors for the active corrosion protection elements of metals when dispersed in organic coatings. The synthesis of precursor slurries was carried out in an electrochemical reactor with aluminum electrodes operating alternately as anodes and cathodes to facilitate metal dissolution and prevent passivation of the electrode surface. The obtained slurries were thermally treated to produce mesoporous alumina particles with adsorbent characteristics suitable for loading corrosion inhibitors. Benzotriazole (BTA) and 8-hydroxyquinoline (8HQ) were chosen as corrosion inhibitors. Dispersed in a commercial polymer matrix and applied to the coating of mild steel samples, the loaded MA improved the corrosion resistance of the coated metal exposed to a simulated marine environment. When physical damage is intentionally caused to expose the underlying metal, the polymer matrix containing BTA-loaded alumina particles retards the corrosion process due to the swelling of the inhibitor from the particles to the exposed bare metal in the scratch. Electrochemical impedance spectroscopy (EIS) measurements showed a marked increase in low-frequency impedance in coatings containing alumina particles, with the BTA-loaded system providing the most durable protection over extended immersion times (with a 50% improvement in corrosion resistance of steel exposed within the scratch). This demonstrates the potential of this approach for long-term corrosion protection applications.