Nanocolloids are nanoparticles suspended in fluids with the aim of improving fluid capability at heat transfer, with a focus on thermal conductivity. The major advantage is the increase in thermal conductivity, with a certain influence on isobaric heat capacity and viscosity. Nevertheless, PEGs are able to create steady suspensions due to their chemical composition and are used in a number of applications. This paper discusses both the advantages and the drawbacks of a suspension of PEG 400 and MWCNT nanoparticles in terms of its relevance for heat transfer applications. Our investigation is built on a complex experimental procedure, as well as an analysis of the state of the art and a discussion of the experimental results in the context of the Prandtl number and thermal diffusivity. This analysis also includes different performance evaluation criteria that are extensively employed both in the heat transfer literature and in practice. The addition of MWCNTs to polyethylene glycol decreases the thermal transport, being influenced by both temperature and the addition of NPs. The results for MWCNT nanocolloids indicate an intensification of the pumping power of up to 29.7%. Also, an interesting option is the use of PEG mixtures as base fluids in order to combine their properties.
Nanofluid development is facing the challenge of instability despite the significant body of research dedicated to developing new nanoparticle-enhanced fluids. Numerous combinations of fluids and particles have been studied; however, the research on surfactants is rather limited, and the results are scattered. This paper is dedicated to the study of two regular polymeric surfactants (PVP and PSS) as well as two polyethylene glycols and one ionic liquid as possible alternatives. The results of a coordinated experiment are followed by a discussion of the density, thermal conductivity, thermal effusivity and viscosity of several samples with the same amount of titanium oxide nanoparticles dispersed in water and different mass concentrations of surfactants (2, 4 and 6%wt.). The results indicated that both the thermal properties and viscosity are negatively affected by the addition of surfactant, which is a drawback. The viscosity remains within a reasonable variation (i.e., between a 0.7 and 1.5% increase) for concentrations of PEG 200, PEG 400 and PSS up to 2%wt. Also, the addition of titania nanoparticles increases the water thermal conductivity by 1.8%, while the addition of surfactant decreases the overall values by around 5%. This disadvantage is amplified when also considering the foam creation, characteristic of all regular surfactants, that limits their real-life applications in turbulent flow.
This study presents a numerical investigation of the laminar forced convection of polyethylene glycol-based nanocolloids within a horizontal pipe. To bridge the gap between theoretical predictions and practical performance, simulations were conducted over a Reynolds number range of 500 to 2000, utilizing a model validated against laboratory-scale experimental data and well-defined boundary conditions. Our analysis focuses on the thermal behavior of polyethylene glycol 200 enriched with metal oxide nanoparticles and multi-walled carbon nanotubes, which were selected for their capacity to enhance thermal conductivity while maintaining manageable viscosity. The results demonstrate that PEG 200-based nanocolloids significantly improve heat transfer performance in the laminar regime. This enhancement is attributed to the superior intrinsic thermal properties of the nanoparticles and the complex synergistic interactions—such as Brownian motion and thermophoresis—between the particles and the PEG base fluid. A critical evaluation of the standard approach of incorporating thermophysical properties into the numerical approach led to significant discrepancies in flow predictions. Additionally, our study establishes that assuming constant thermophysical properties during the heating process introduces simulation errors exceeding 10%. These findings underscore the necessity of incorporating temperature-dependent, experimentally validated data into numerical models to ensure predictive accuracy. Ultimately, this work advocates for a nuanced approach to nanocolloid design that prioritizes the specific chemical and rheological compatibility between nanoparticle types and the base fluid.
Polyethylene glycols (PEGs) are emerging as superior and accessible phase change materials and heat transfer fluids, offering improved thermal properties over conventional thermal oils to meet the demand for innovative, sustainable energy solutions. While general research on PEG performance is still scarce, this paper contributes relevant experimental data. As part of a broad investigation into PEG and PEG-based nanocolloids, this experiment helps to clarify the true potential of these new fluids by outlining both their key advantages and their operational limitations. Consequently, PEG 200 and two PEG 200 + PEG 400 mixtures were considered as base fluids for manufacturing MWCNT nanocolloids, resulting in 15 samples that were thoroughly investigated in terms of density, viscosity and isobaric heat capacity variation with both nanoparticle concentration and temperature. Results revealed that nanocolloid density follows the basic rules for nanoparticle-enhanced fluids, with moderate increase with nanoparticle addition and temperature. Viscosity increased with MWCNT concentration and decreased with temperature, while isobaric heat capacity upsurges with nanoparticle addition. These findings are critical, as they can shed some light into the practical benefits, while clearly explaining the potential drawbacks, of employing these novel fluids in heat transfer applications.
Rotary swaging (RS) is applied for the manufacturing of bars, stepped shafts, tubes with complex internal profiles, bimetallic composites, and similar products. This process falls under the category of severe plastic deformation (SPD) methods, which produce ultrafine-grained materials that provide superior properties in service. Our study investigated the effect of cold RS on the structure, grain size, and microhardness of AISI 304 stainless steel and CK45 carbon steel. Tubular specimens were processed by RS with the purpose of obtaining conical parts with a closed end, achieving a maximum reduction of nearly 44%. Samples were taken by longitudinal sectioning along the diameter from three zones with different degrees of deformation and subjected to structural analysis using scanning electron microscopy (SEM). The investigations were complemented by microhardness measurements in the axial direction for samples of both steels. The resulting structures revealed material texturing and a continuous decrease in grain size with increasing swaging ratio. The average grain size was reduced by approximately 46% in AISI 304 steel and by around 50% in CK45 steel. The microhardness of the materials increased by about 179% for AISI 304 steel and by approximately 95% for CK45 steel. The obtained results are discussed, highlighting the effect of cold RS processing on the two steels studied.