This work presents an Internet of Things (IoT) node designed for low-power agrifood chain tracking in remote areas, where long-range terrestrial communication is either unavailable or severely limited. The novelty of this study lies in the development and characterization of an IoT node prototype that leverages direct-to-satellite connectivity through a geostationary Earth orbit (GEO) satellite, using long-range frequency-hopping spread spectrum (LR-FHSS) modulation in the licensed S-band. The prototype integrates a microcontroller unit that manages both the radio modem and a suite of sensors, enclosed in a plastic box suitable for field deployment. Characterization in an anechoic chamber demonstrated a maximum effective isotropic radiated power (EIRP) of dBm, sufficient to establish a reliable satellite link. The onboard sensors provide global positioning as well as measurements of acceleration, temperature, humidity, and solar radiation intensity. Prototype performance was assessed in two representative scenarios: stationary and mobile. Regarding energy consumption, the average charge drained by the radio modem per transmission cycle was measured to be 356 mC. With a battery pack composed of four 2500 mAh NiMH cells, the estimated upper bound on the number of transmitted packets is approximately 25,000.
This work introduces the load-modulation technique to improve the power handling capabilities of envelope tracking (ET) power amplifiers. It is based on an auxiliary amplifier capable to inject at the main amplifier output terminal a copy of its input signal, properly phased and scaled in magnitude. By this approach, the ET output termination can track the bias supply thus maintaining the maximum dynamics of both current and voltage at the device output terminal. The proposed load-modulated envelope tracking (LM-ET) is demonstrated through the design analysis, and the development of a prototype characterized in the 3600 – 3800 MHz frequency bandwidth. Experimental results demonstrate an improvement of 3 dB at 5 dB power back-off maintaining the overall efficiency degradation of maximum 9%.
This work presents an Internet of Things (IoT) node based on Geostationary Earth Orbit (GEO) satellite communications. The work addresses the issues of low-power agrifood chain tracking in remote areas, where long range terrestrial communications are either denied or impaired. The novelty of the work is the development and characterization of the IoT node with a dedicated radio modem unit providing GEO satellite connectivity. This enables real-time tracking and sensing. As preliminary design, an IoT node conceived for cattle tracking is assembled and tested. The node is equipped with a microcontroller unit, controlling the radio-mode unit and a suitable sensor set installed in the IoT node itself. The set of sensors is capable to acquire position coordinates, acceleration, temperature, humidity, and intensity of solar radiation. The radiating features of radio-modem unit, embedded in the IoT node plastic enclosure, were characterized and exhibits a maximum transmitting effective isotropic radiated power of 27.5 dBm . The experiments measured the average charge drained by the radio-modem unit per cycle, resulting in 356 mC. Considering a battery pack composed of four 2500 mAh AA NiMH, the estimated number of cycles is approximately 25,000.
This paper presents an IoT node architecture suitable for Agrifood supply chain tracking, based on GEO LoRa satellite connectivity. The paper presents data about the current consumption in different profile and, on the basis of a realistic applicative scenario, which include position and physical parameters tracking, assesses a battery life of about 7 years.
In this paper a mm-Wave, temperature-calibrated K-band noise source built with commercial on-the-shelf (COTS) components is demonstrated. The proposed source includes a Si-Ge Heterojunction Bipolar Transistor (HBT) using its base-emitter (BE) junction driven into avalanche breakdown, as the main noise-generating element. Excess Noise Ratio (ENR) values reaching 10.8 dB were obtained with a 6.71 mA breakdown current, in a 24 GHz to 32 GHz bandwidth and a 21 °C to 102 °C device temperature excursion, with no impedance matching. A calibration model is also provided, which fits ENR magnitude with an average error less than 0.05 dB, when considering the maximum current and temperature ranges. An ENR drift error of 0.8 dB was instead reported for the uncalibrated source.
16 September 2025 in International Journal of Microwave and Wireless Technologies
This paper presents the development and characterization of a wideband noise source, involving Commercial Off-The-Shelf components. The noise source relies on avalanche noise generation by driving the base-emitter junction of a packaged Si–Ge Heterojunction Bipolar Transistor into reverse breakdown. The paper discusses the noise source operation principle and its extensive characterization in both mm-Wave K band, as well as in C and X bands. Two prototypes were implemented without including output impedance matching, such as to preserve the wideband capabilities of the noise source. Performances were validated in terms of output Excess Noise Ratio (ENR), values reaching 10.8 dB were obtained for the K band at 6.71 mA breakdown current, in a 24–32 GHz bandwidth and $21-102^{\circ}\mathrm{C}$ device temperature excursion. A calibration model is also provided, which fits ENR fluctuations with an average error under 0.05 dB, when considering the maximum current and temperature excursions, as compared with 0.8 dB ENR drift reported for the non-calibrated source. The C and X band validation in 4–6 and 10–12 GHz frequency ranges highlights ENR reaching 25.6 and 22.6 dB, respectively, at 6.9 mA bias current.