The high-volume fraction SiC/Al composite is the new type of electronic packaging material, which plays an important role in the field of high-power integrated circuits. In this study, SiC/Al composites with high-volume fraction of SiC particles were prepared by vacuum pressure infiltration. The influence of SiC particle size and NH₄HCO₃ on the pores in the preform was explored, aiming to accurately adjust the volume fraction of SiC to meet the thermal performance requirements in different fields. In addition, the preform was infiltrated with different Al alloys, and the relationship between the porosity and thermal conductivity of SiC/Al was studied. For the SiC preform, the volume fraction of SiC can be adjusted regularly when 12 μm and 100 μm SiC particles are mixed in different proportions, and the volume fraction reaches the maximum when the proportion of coarse particles is about 77%. NH₄HCO₃ is conducive to the connectivity of pores in the preform, and about 40 vol.% of NH₄HCO₃ can effectively increase the porosity of the preform. Thermal conductivity is sensitive to the porosity of composites, especially in the range of 2.5–4.5%. A simple application of the Hasselman–Johnson model and a new thermal conductivity model, λ_d, established in this article, offer a good agreement with the experimental results.

In this study, Al-Mg alloys were prepared by vacuum + argon-protected casting. The effects of Sc microalloying on the microstructure and mechanical properties of Al-Mg alloy were studied. The strengthening mechanism of Al-Mg alloy with Sc was discussed. The results show that the average grain size of as-cast Al-Mg alloy with Sc reaches 36.07 μm, which is 74.4% smaller than that of alloy 1 without refiner and 32.0% of alloy 2 with 0.15% Ti. The alloy with Sc has excellent comprehensive mechanical properties, with a tensile strength of 274 MPa and an elongation of 29.67%, and its tensile strength is 10.6% higher than alloy 1 and 7.9% higher than alloy 2. There exist two kinds of fine particles in as-cast Sc-containing Al-Mg alloy, nucleated particles Al₃Sc, and dispersed second-phase particles Al₃(Sc, Ti). The main strengthening mechanisms of the as-cast Al-Mg alloy with Sc reveal the solid solution strengthening of Mg and the fine-grain strengthening effect caused by Sc, accounting for 57.7% and 23.9% to strengthening contribution, respectively.

In this study, large-sized Al–Zn–Mg–Cu alloy billets were prepared by direct chill casting imposed with annular electromagnetic stirring and intercooling; a process named uniform direct chill casting. The effects of uniform direct chill casting on grain size and the alloying element distribution of the billets were investigated and compared with those of the normal direct chill casting method. The results show that the microstructures were refined and the homogeneity of the alloying elements distribution was greatly improved by imposing the annular electromagnetic stirring and intercooling. In uniform direct chill casting, explosive nucleation can be triggered, originating from the mold wall and dendrite fragments for grain refinement. The effects of electromagnetic stirring on macrosegregation are discussed with consideration of the centrifugal force that drives the movement of melt from the central part towards the upper-periphery part, which could suppress the macrosegregation of alloying elements. The refined grain can reduce the permeability of the melt in the mushy zone that can restrain macrosegregation.

This study presents a modified annular electromagnetic stirring (M-AEMS) melt treatment suitable for a large-volume and high-alloyed aluminum alloy. A 3D computational model coupling an electromagnetic model with a macroscopic heat and fluid-flow model was established by using Ansoft Maxwell 3D and Fluent from ANSYS workbench, and the effects of the electromagnetic shielding ring, the height of the magnet yoke, the shape of the iron core, and the internal cooling mandrel on the electromagnetic, thermal and flow fields were studied numerically. Based on the optimal technical parameters, the effectivity of the M-AEMS process by using 7075 alloy was validated experimentally. The results show that a favorable electromagnetic field distribution can be achieved by changing the magnet yoke height, the iron-core shape and the electromagnetic shielding ring, and the melt temperature of the 7075 alloy can drop rapidly to the pouring temperature by imposing the internal cooling mandrel; compared with ordinary annular electromagnetic stirring, the M-AEMS process creates a lower magnetic strength near the melt top, beneficial for stabilizing the melt surface; meanwhile, it yields a higher magnetic strength near the melt bottom, which increases the shear rate and ensures an optimal stirring effect. Therefore, M-AEMS works more efficiently because the thermal and composition fields become uniform in a shorter time, which reduces the average grain size and the composition segregation, and a more stable melt surface can be obtained during treatment, which reduces the number of air and oxide inclusions in the melt.

In this paper, the effect of adding the refiner Sc to the high Zn/Mg ratio 7xxx series aluminum alloy melt on the hot tearing performance, microstructure, and mechanical properties of the alloy is studied. The hot tearing performance test (CRC) method is used to evaluate the hot tearing performance of the alloy. The squeeze casting process was used to form solid cylindrical parts to analyze the structure and properties of the alloy. This study shows that the hot cracking sensitivity of the alloy after the addition of the refiner Sc is significantly reduced. The ingot grain size is significantly reduced, and the average grain size is reduced from about 86 μm to about 53 μm. While the mechanical properties are significantly improved, and the tensile strength reduced from 552 MPa is increased to 571 MPa, and the elongation rate is increased from 11% to 14%.