This study investigated the disintegration of sewage sludge through the Fenton process. The study was conducted by both the conventional Fenton-type process (CFP) (Fe2+/H2O2) and the Fenton-type process (FTP) (nZVI/H2O2). Experiments were performed using different pH, catalyst iron (Fe2+ and nZVI), and H2O2 dosages. Different parameters such as the degree of disintegration (DD), soluble chemical oxygen demand (SCODS), and particle size distribution were studied to investigate the effects of CFP and FTP processes on the disintegration of sludge. In addition to these parameters, scanning electron microscope, Fourier-transform infrared spectroscopy, and X-ray diffraction analyses were done to determine the changes in sludge characterization before and after disintegration. In the study, the optimal catalyst iron was determined to be (Fe2+ and nZVI) 4 g/kg total solids (TS), and the H2O2 dosage was determined to be 10 g/kg TS. The experiments were performed with consideration of the 1-h oxidation time. While DD was found to be 31.8% and the SCODS was found to be 364 mg/L for FTP, DD and SCODS were found to be 14.1% and 256 mg/L for CFP, respectively.
1 March 2017 in Ecological Chemistry and Engineering S
In the work, adsorption of Cu2+ ions onto almond shell were investigated under different operational conditions. Almond shell was used without any pretreatment prior to the tests. The optimum conditions for adsorption of Cu2+ ions through almond shell were determined to be; pH 5.0, temperature 20°C, shaking rate 125 rpm, sorbent dose 0.3 g and initial Cu2+ ion concentration 50 mg/dm3. The equilibrium duration of the system was 60 minutes. The sorption capacities of the sorbents were predicted with the aid of equilibrium and kinetic models. The interactions of peanut shell with metal ions were constituted by SEM, EDX, FT-IR, XRD and AFM. The pseudo-first-order, pseudo-second-order, Weber-Morris, Elovich model and Bangham kinetic models were applied to test the experimental data. The Cu+2 ions adsorption onto almond shell was better defined by the pseudo-second-order kinetic model, for initial pH. The equilibrium data were evaluated using Langmuir, Freundlich, Temkin, D-R and Harkins Jura isotherms. The highest R2 value in isotherm studies was obtained from Langmiur isotherm (R2 = 0.98) for the inlet concentration.
1 December 2018 in Ecological Chemistry and Engineering S
In this study, ANN (artificial neural network) model was applied to estimate the Ni(II) removal efficiency of peanut shell based on batch adsorption tests. The effects of initial pH, metal concentrations, temperature, contact time and sorbent dosage were determined. Also, COD (chemical oxygen demand) was measured to evaluate the possible adverse effects of the sorbent during the tests performed with varying temperature, pH and sorbent dosage. COD was found as 96.21 mg/dm3 at pH 2 and 54.72 mg/dm3 at pH 7. Also, a significant increase in COD value was observed with increasing dosage of the used sorbent. COD was found as 12.48 mg/dm3 after use of 0.05 g sorbent and as 282.78 mg/dm3 after use of 1 g sorbent. During isotherm studies, the highest regression coefficient (R2) value was obtained with Freundlich isotherm (R2 = 0.97) for initial concentration and with Temkin isotherm for sorbent dosage. High pseudo-second order kinetic model regression constants were observed (R2 = 0.95-0.99) during kinetic studies with varying pH values. In addition, Ni(II) ion adsorption on peanut shell was further defined with pseudo-second order kinetic model, since qe values in the second order kinetic equation were very close to the experimental values. The relation between the estimated results of the built ANN model and the experimental results were used to evaluate the success of ANN modeling. Consequently, experimental results of the study were found to be in good agreement with the estimated results of the model.
12 September 2022 in Journal of the Iranian Chemical Society