A chirp-mismatch echo signal can be generated by exchanging the I and Q baseband signals of a received SAR signal. In this paper, the basic generation principles of a chirp-mismatch echo signal are analyzed. Then, a suppression jamming method with controllable jamming position and coverage area is proposed. This method firstly performs chirp-mismatch processing on the received SAR signals, then controls the range jamming coverage and center position through range shift-frequency modulation and time delay, and controls the azimuth jamming coverage and center position through motion modulation and azimuth shift-frequency modulation. Theoretical analysis and simulation results show that this method can effectively control the location and coverage of a jamming result without convolution modulation, and it is easy to implement in engineering. The simulation results verify the correctness of the theoretical model, which can provide a basis for the implementation and application of SAR jamming based on the active radar transponder.

GaoFen-3, the first polarimetric SAR satellite of China, carried out polarimetric calibration experiments using C-band polarimetric active radar calibrators (PARCs), trihedral corner reflectors (TCRs), and dihedral corner reflectors (DCRs). The calibration data were firstly processed referring to the classic 2 × 2 receive R and transmit T model for radar polarimeter systems, first proposed by Zebker, Zyl, and Held, and Freeman’s method based on PARCs, but the results were not good enough. After detailed analysis about the GaoFen-3 polarimetric system, we found that the system had some nonlinearity, then a new imbalance parameter was introduced to the classic model, which is equivalent to the $\gamma$ proposed in Freeman’s paper about a general polarimetric system model. Then, we proposed the calibration data processing algorithm for GaoFen-3 based on the improved model and obtained better results. The algorithm proposed here is verified to be suitable for GaoFen-3 and can be applied to other spaceborne and airborne fully-polarimetric SAR systems.

In this paper, additional reference height errors, caused by the penetration depth and Signal to Noise Ratio (SNR) decorrelation in desert regions in L-band spaceborne bistatic interferemetric SAR, will introduce significant errors in nowadays baseline calibration method based on distributed target and consequent DEM products. To quantify these two errrors, this paper takes the TwinSAR-L mission as an example, gives an introduction of TwinSAR-L, outlines the theoretical baseline accuracy requirements that need to be satisfied in the TwinSAR-L mission and addresses the additional reference height errors caused by the penetration depth and SNR decorrelation in desert regions in general by taking the TwinSAR-L mission as an example. Based on ALOS-2 data from a dry desert region in the east of Xing Jiang, this paper quantitatively analyzes these additional reference height errors. The results show that the additional reference height errors resulted from the penetration depth and the SNR decorrelation are 1.295 m and 1.39 m, respectively, which would even cause 6.4 mm and 8.6 mm baseline calibration errors. These errors would seriously degrade the baseline calibration accuracy and the consequent DEM product quality. Therefore, our analysis is of great significance not only for baseline calibration, but also for high-quality DEM’s generation, accuracy assessment and geophysical parameters’ quantitative inversion and application.

LuTan-1 (LT-1) is a bistatic synthetic aperture radar (BiSAR) system consisting of two identical L-band SAR satellites. The bistatic mode of LT-1 plays a critical role in generating high-precision digital elevation models (DEMs), which requires precise geometric calibration of initial range and azimuth times for both SARs to ensure the reliability and quality of geolocation. However, existing geometric calibration methods predominantly focus on monostatic SAR systems, with limited literature on slave SAR calibration in bistatic systems. This research addresses this gap by establishing geometric calibration models for both SARs based on signal echo history and the range–Doppler model. The geometric errors are effectively resolved using corner reflector data from Xinjiang, China. Through statistical analysis of LT-1 SAR images acquired between July and November in bistatic mode, this paper has demonstrated range delay accuracy of better than 5 ns and azimuth time accuracy of better than 0.1 ms. This level of precision translates into a positional accuracy better than 0.8 m. The proposed models have been successfully applied to geometric calibration, providing precise geolocation for LT-1, thus enhancing its utility for a wide range of Earth observation applications. This paper is the first endeavor to present the assessment of the geometric calibration and geolocation accuracy of LT-1 and discuss the results of the bistatic geometric calibration of the master and slave SARs in a BiSAR formation.

The Terrain Wide-swath Interferometric L-band Synthetic Aperture Radar (TwinSAR-L) mission is a spaceborne bistatic synthetic aperture radar (SAR) mission to derive a high-quality global digital elevation model (DEM). The prerequisite of the high-accuracy DEM is knowing the interferometric baseline with high precision. The challenging problem is that the baseline of the bistatic system is highly dynamic due to the fast relative motion between the two satellites. In this paper, a pixel-related baseline model based on the geometrical shift is proposed to accurately reflect the position change of satellites. The baseline error is then calibrated using height gradient information and a small number of point targets with a slight incidence angle difference, eliminating the need for low-frequency corner reflectors and avoiding the difficulty of selecting a calibration site. The proposed method has been successfully exploited during the initial Commissioning Phase of TwinSAR-L, demonstrating its effectiveness in evaluating the precise baseline and supporting the generation of high-precision DEM.

The trihedral corner reflector (TCR) is widely used as the calibration device in monostatic synthetic aperture radar (SAR) calibration, and the performance of the TCR in radiometric calibration has been studied and verified in depth. As for the bistatic SAR system calibration problem, there have been few published studies. There is a lack of knowledge regarding the exact bistatic radar cross-section (RCS) pattern of TCR with different bistatic angles, and it is also not clear whether the TCR can be used as the calibration target in bistatic SAR. Moreover, the bistatic and monostatic radar cross-section (RCS) characteristics of the TCR are different, even if the bistatic angle is very small. Therefore, the feasibility, design, and deployment requirements of the TCR for bistatic SAR calibration should be carefully investigated. In this paper, we outline the theoretical and practical requirements that need to be satisfied when choosing appropriate calibration devices for bistatic radiometric calibration. Based on these requirements, we analyzed the bistatic RCS patterns using electromagnetic simulation, and concluded that the TCR is feasible for bistatic SAR calibration under relatively small bistatic angles (less than 6°). The change of TCR boresight with the bistatic angle is not considered generally. However, we found that the TCR boresight and peak RCS will change with the bistatic angle. We have also proposed that the bistatic angle can be extended to 20° by taking the change of the TCR boresight into account. In this condition, we should get the TCR boresight according to the bistatic angle and then align it during the deployment. Both of these two conditions have their own unique advantages. Different error sources of TCR RCS from manufacture, misalignment, and deformation were investigated quantitatively with simulations, which can provide a theoretical basis for how to design a suitable TCR and guarantee the calibration accuracy for bistatic calibration. In addition, simulation results are different from those of monostatic calibration. Through experiments, we have further verified the feasibility by comparing the quality of bistatic SAR images and point target energy with several typical bistatic angles as the TCR boresight is considered or not. If the bistatic angle is larger than 6°, taking the TCR optimum boresight into account can improve imaging quality and point target energy.