UV sensors hold significant promise for various applications in both military and civilian domains. However, achieving exceptional detectivity, responsivity, and rapid rise/decay times remains a notable challenge. In this study, we address this challenge by investigating the photodetection properties of CdS thin films and the influence of surface-deposited gold nanoparticles (AuNPs) on their performance. CdS thin films were produced using the pulsed laser deposition (PLD) technique on glass substrates, with CdS layers at a 100, 150, and 200 nm thickness. Extensive characterization was performed to evaluate the thin films’ structural, morphological, and optical properties. Photodetector devices based on CdS and AuNPs/CdS films were fabricated, and their performance parameters were evaluated under 365 nm light illumination. Our findings demonstrated that reducing CdS layer thickness enhanced performance concerning detectivity, responsivity, external quantum efficiency (EQE), and photocurrent gain. Furthermore, AuNP deposition on the surface of CdS films exhibited a substantial influence, especially on devices with thinner CdS layers. Among the configurations, AuNPs/CdS(100 nm) demonstrated the highest values in all evaluated parameters, including detectivity ( Jones), responsivity (13.86 A/W), EQE (47.2%), and photocurrent gain (9.2).
Cu2SnS3 (CTS) thin film has been produced for 30 ccm sulphur flux rate at 30 minutes annealing durations at 550 oC temperature. CTS thin film’s crystalline structure has been investigated and crystalline size, lattice parameters, dislocation density and microstrain, crystalline number have also been determined. The CTS thin film’s morphological and optical properties have been examined and thoroughly interpreted. Mo/CTS/CdS/AZO solar cell has been modelled based on CTS thin film produced at the present work, using SCAPS-1D simulation programme. Voc, Jsc, FF, conversion efficiency and photovoltaic parameters have been determined depending on neutral defect density at the interface, coefficient of radiative recombination, Auger electron/hole capture’s coefficient and operation temperature of CTS solar cell. As a consequence of simulation study, ideal efficiency of CTS solar cell has been determined to be 3.72 % and all the data obtained in this study have been presented, interpreted and concluded to be original results.
30 December 2021 in Middle East Journal of Science
Plasmonic metal nanoparticles (NPs), such as Ag, Au, Cu NPs, attracts a lot of interest due to their notable applications in biological, and chemical sensing. Researchers have studied on plasmonic metal NPs which have exceptional optical properties in a large spectral region. Metal NPs form a unique surface plasmon resonance (SPR) peak that is in the electromagnetic spectrum’s visible part. The peak of SPR firmly depends on the NP’s size, shape, dielectric constant, and medium that the particle is in. Light interacts with nanoparticles that are smaller than the wavelength of incident light in localized surface resonance. That leads Localised Surface Plasmon Resonance (LSPR) in which an oscillating local plasma around NP with a certain frequency form. LSPR detection is the most common method for wavelength shift measurement. Analyte absorption causes a change in the local dielectric constant and thus LSPR peak shifts. Biological molecules such as proteins and antibodies can sensitively be detected as they change the local dielectric environment. Therefore, Ag or Au metal NPs can be used as sensor by employing LSPR wavelength shift technique. Among the metal NPs, Ag has a relatively higher refractive index sensitivity. Since Ag NPs have a shaper LSPR peak, they generate more precise measurements. In our work, we have produced plasmonic Ag NPs with various sizes and spherical shapes by employing Pulsed Laser Deposition (PLD). We investigated the LSPR peaks of produced plasmonic Ag NPs by UV-Vis spectroscopy. Moreover, biosensor properties of plasmonic Ag NPs are investigated by binding Protein A molecules to surface of the NPs. That produced a LSPR wavelength shift of around 100 nm/RIU.
31 December 2024 in International Journal of Pure and Applied Sciences
Plasmonic gold nanoparticles exhibit exceptional optical properties, particularly Lo-calised Surface Plasmon Resonance, which makes them ideal candidates for sensor applications. These nanoparticles are highly sensitive to changes in their surrounding environment, allowing for precise detection of molecular interactions and environ-mental shifts. In this study, we investigate the sensor properties of gold nanoparticles produced via Pulsed Laser Deposition, a clean and versatile method that allows for precise control over particle size, morphology, and distribution without the need for chemical reagents. Pulsed Laser Deposition process was optimized by adjusting laser fluence, pulse duration, and deposition time to produce gold nanoparticles with tuna-ble plasmonic properties. The structural and optical characteristics of gold nanoparti-cles were analyzed using scanning electron microscopy, and UV-Vis spectroscopy, confirming that the size and morphology of the particles were controllable through the deposition parameters. The sensor performance of gold nanoparticles was evalu-ated through localised surface plasmon resonance measurements, which demonstrated their sensitivity to small changes in the refractive index of the surrounding medium. Specifically, the shift in localised surface plasmon resonance peak was measured up-on exposure to different analytes, including protein A where a wavelength shift of 50 nm measured, indicating the high sensitivity of these nanoparticles for biosensing ap-plications. The results suggest that Pulsed Laser Deposition-produced gold nanoparti-cles possess promising sensor properties for real-time detection and environmental monitoring, offering an efficient and reproducible platform for a wide range of sens-ing applications.