Osmotic dehydration is a dehydration technique that allows the preservation of the organoleptic characteristics of the food and its nutritional properties compared to other preservation methods, such as hot air drying or solar drying. Studies on this dehydration process are usually carried out on a laboratory scale and with the constant presence of the evaluator, interrupting the process for sampling. That is why the main objective of this research was to build an automated osmotic dehydration equipment implementing the Internet of Things (IoT). The measurable factors involved in the process were determined, and the necessary sensors and actuators were chosen along with the best IoT alternative for the process. A prototype was built, which allows for controlling the agitation of the osmotic solution, temperature control, and remote monitoring of concentration and temperature variables. The equipment was tested by evaluating its performance in the dehydration of melon and apple, where the ANOVA tests demonstrated the significance (p < 0.05) of the factors chosen as part of the equipment design and their interaction with the process. In the apple samples, a weight loss of up to 44.007% and a water loss of 53.234% were obtained. For melon, the process showed greater efficiency in dehydration, with values of 75.259% for weight loss and 75.979% for water loss.
15 December 2024 in Current Research in Nutrition and Food Science Journal
Drying has been the most widely used method of dehydration since ancient times; however, its use generates high energy costs, due to the long duration of the process. On the other hand, the exposure of foods to high temperatures for long periods of time tends to considerably affect not only their organoleptic characteristics, but also their nutritional content. An alternative to these problems is osmotic dehydration, which allows generating a partial dehydration without deteriorating the food's properties. In this way, the food begins its drying process with a reduced moisture content, thus reducing the drying time, saving energy costs and avoiding exposing the food to heat for long periods of time. The methodology consisted of evaluating the osmotic dehydration process of melon at osmotic concentrations of 45 °Bx and 60 °Bx and immersion times of 120 and 180 minutes, to be subsequently dried at 50°C until reaching a minimum humidity of 15%. The osmotic dehydration tests demonstrated the significance (p < 0.05) of the factors studied in water loss, weight loss and solids gain. Water losses between 48.393% and 68.204% were achieved, where drying time was reduced in a range between 23% and 46%. The treatment that generated the shortest drying time was the one that had as pretreatment conditions of 60°Bx and 180 minutes of immersion.
Osmotic dehydration (OD) is an effective pre-treatment for fruit preservation, but conventional processes often lack precision due to manual control of critical variables. This work reports the design and validation of an automated OD system integrating a programmable logic controller (PLC), human–machine interface (HMI), and IoT-enabled sensors for real-time monitoring of syrup concentration and process temperature. Mango (Mangifera indica) cubes were treated under a 23 factorial design with sucrose concentrations of 45 and 50 °Brix, immersion times of 120 and 180 min, and temperatures of 30 and 40 °C. Validation demonstrated that the IoT hydrometer achieved strong agreement with reference devices (R2 = 0.985, RMSE = 0.36 °Brix), while the PLC-integrated tank sensor also demonstrate improved performance over existing calibrated thermometer (R2 = 0.992, MAE = 0.20 °C). ANOVA indicated that concentration, temperature, and time significantly affected water loss and weight reduction (p < 0.01), with temperature being the dominant factor. Water loss ranged from 18.62% to 39.15% and weight reduction from 9.48% to 34.47%, while maximum solid gain reached 9.31% at 50 °Brix and 40 °C for 180 min, with stabilization consistent with case hardening. Drying kinetics were best described by the Page model (R2 > 0.97). The findings highlight the effectiveness of the system for precise monitoring and optimization of OD processes.
25 August 2025 in Current Research in Nutrition and Food Science Journal
Osmotic dehydration removes water from fruits using hypertonic solutions, enhancing shelf life and quality. However, little research explores natural sweeteners like panela as osmotic agents in developing nutritious, acceptable apple-based snack products. The objective of this research was to evaluate the effect of osmodehydration pretreatment with panela in development of apple snacks (Malus domestica). The methodology evaluated was through an osmotic dehydration process of apple. Panela syrups were used at concentrations of 45 ºBrix and 50 ºBrix with immersion times of 120 and 180 minutes and followed by drying for 8 hours at 55 ºC. Sensory evaluation was performed with student as participants using five-point hedonic scale. For the previously mentioned data analysis, a completely randomized design (CRD) with a 2x2 factorial setup was employed, whereas a five-point hedonic scale was utilized for the sensory evaluation. Using a 2x2 factorial statistical design, it was possible to determine p-values < 0.05, indicating a significant level of confidence in the effects of concentration and temperature on water loss (WL), weight reduction (WR), and solids gain (SG). Results showed weight loss (WR) which was 30.28% and water losses (WL) of up to 31.87%. On the other hand, the lowest solids gain was 2.60% while the highest was 5.64 Finally, the sensory analysis showed that the samples pretreated with osmodehydration T4 (50 ºBrix–180 min) and T3 (45 ºBrix–180 min) had higher acceptability, likewise the least accepted by the panela were T1, S/T (without treatment) and T2 in descending order.
16 October 2023 in VISUAL REVIEW. International Visual Culture Review / Revista Internacional de Cultura Visual
The automation courses established in the curricula of food engineering careers need to be strengthened and updated in order to improve student learning and new trends related to process automation such as IoT are covered. A review of the literature was carried out whose objective was to obtain an overview of the status of automation courses in food engineering careers and to share improvements to strengthen these in order to ensure that graduates acquire the necessary skills and competences to perform in today's industry.
This study presents the design and development of an innovative osmotic dehydrator integrating a Programmable Logic Controller (PLC), Human-Machine Interface (HMI), and IoT sensors dedicated to real-time, automated monitoring and control of syrup concentration—a critical but often overlooked parameter. Additional key process variables such as temperature, recirculation rate, and time are also precisely controlled to optimize the osmotic dehydration process and improve food preservation quality and operational efficiency. Validation included eight treatments combining two sucrose concentrations (45 and 50 °Brix), two temperatures (30 and 40 °C), and two immersion times (120 and 180 minutes). Weight reduction, water loss, and solid gain were measured. The treatment with the highest concentration, temperature, and time showed the greatest mass transfer. Statistical analysis revealed significant effects (p < 0.001) and strong fits (R² = 0.995) for weight and water loss, while solid gain showed moderate fit (R² = 0.772). Kinetic modeling using the Page model best described drying dynamics (R² > 0.97). Results suggest the automated system can improve operational efficiency and product quality. However, practical validation under real conditions is needed to confirm functionality and scalability. This work advances osmotic dehydration technology by combining automation with precise process control, aiming to enhance food processing applications.