Qiaoping Kong

Dr. Qiaoping Kong


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2021 in Chemosphere
Verified
Journal Article
Closed access
JMJingde Ma
Jingde Ma
JWJingyue Wei
Jingyue Wei
QKQiaoping Kong
Qiaoping Kong
ZLZemin Li
Zemin Li
JPJianxin Pan
Jianxin Pan
CWChaohai Wei
Chaohai Wei

18 September 2025 in Processes
Verified
Journal Article
Open access
PDF file
WMWeiwei Ma
Weiwei Ma
HHHongrong Huang
Hongrong Huang
GZGuangjin Zhu
Guangjin Zhu
XWXueqing Wang
Xueqing Wang
QKQiaoping Kong
Qiaoping Kong
Xueqing ShiXueqing Shi
Xueqing Shi
Lithium (Li) ion sieve is considered to have great potential in the selective extraction of Li+ from complex Li+-containing brine owing to its cost-effectiveness, excellent adsorption performance, and environmental friendliness. Nevertheless, the defects of complex regulation and control of technological parameters in the preparation process of Li ion sieve and poor recycling efficiency limit its application. In this study, spinel-type H4Ti5O12 ion sieves (HTO) were successfully prepared through a high-temperature solid-state method for recovering Li+ from aqueous resources. Through the experiment of optimizing the key preparation process parameters of HTO, it was found that the optimum preparation conditions were as follows: lithium ion source of CH3COOLi‧H2O, calcination temperature of 800 °C, and acid (HCl) washing concentration of 0.3 mol/L. The uptake of Li+ by HTO aligned with the pseudo-second-order kinetic model, which was a chemical adsorption process controlled by reversible Li–H ion exchange reaction. HTO exhibited extremely high regeneration cycle characteristics, and after five cycles, it retained 96.06% of its initial adsorption capacity. The present work highlighted that spinel-type HTO has high industrial application potential in the field of Li+ recovery from oilfield brine.

1 January 2022 in Desalination and Water Treatment
Verified
Journal Article
Closed access
JLJian-Jun Lian
Jian-Jun Lian
MWMeng Wu
Meng Wu
BCBo Chen
Bo Chen
LZLin Zhang
Lin Zhang
FZFan-Jie Zhou
Fan-Jie Zhou
JWJing Wu
Jing Wu

12 July 2021 in Research Square
Verified
Preprint
Open access
PDF file
LXLiping Xiao
Liping Xiao
YLYan Li
Yan Li
QKQiaoping Kong
Qiaoping Kong
YLYunlong Lan
Yunlong Lan
To control eutrophication and recover phosphate from wastewater, a calcium carbide slag and red mud composite material (CR-LDH) was prepared using industrial waste as raw material for phosphorus adsorption. The morphology and structure of synthesized CR-LDH was characterized by FT-IR, SEM, EDS and XRD measurements. The experimental data can be well described by pseudo-second-order kinetics and Langmuir isotherm models, suggesting that the adsorption process of CR-LDH with respect to phosphate is a chemical and monolayer process. The theoretical maximum adsorption capacity obtained by Langmuir isotherm model is 16.06 mg·g-1 at 25 oC. The intra-particle diffusion model fitting results indicated that the adsorption of phosphate by CR-LDH was controlled by both liquid membrane diffusion and intra-particle diffusion. Phosphate was bound to CR-LDH via synergistic effect of physical adsorption, ion exchange, anion intercalation and chemical precipitation as evidenced from a combination of microscopic analysis and adsorption mechanism study. The actual phosphate-containing wastewater investigation showed that CR-LDH not only exhibited good removal effect on phosphate, but also could greatly reduce turbidity, COD and ammonia nitrogen, which was suitable for disposal of practical wastewater. These results indicate that CR-LDH can be considered as potential adsorbent for the treatment of phosphate-containing wastewater, which will be helpful to achieve the goal of "treating waste with waste and turning waste into treasure".