The effects of linker length on nanosheet dimensions and properties are investigated through the ultrasonic liquid exfoliation of an isoreticular series of layered metal–organic frameworks.
Polyisocyanurate (PIR) foams are widely used as insulation, but their performance reduces over time leading to higher heating costs. The addition of metal–organic frameworks have potential for improvement of PIR foam's lifetime performance.
Polyisocyanurate (PIR) foams are widely used to insulate buildings, but their performance reduces over time leading to wasted energy and higher heating costs. High molecular weight gases used to blow the foams gradually diffuse out and are replaced by air leading to an increase in thermal conductivity. A wide variety of additives have been tested to improve the barrier properties of polymers including metal-organic frameworks (MOFs) which have proved promising candidates thanks to their tunable surface chemistry. In this work, a new and robust method for determining gas loss from rigid PIR foams has been developed, and utilised to determine the effect of different MOF additives on gas loss. An accelerated ageing method was developed, in which the mass of a fixed volume of foam was kept in an oven at 70 °C and weighed at 24 hour time intervals. This was found to provide reproducible measurements of gas loss over a period of 28 days with a variation of 1.1 % by mass for typical samples. Five different MOFs were added to polyisocyanurates, and their effects on cell size, closed cell content, and gas loss over time were measured. Cu(ABDC)(DMF) was found to enhance the gas retention of PIR foams with minimal change to cell size or closed cell content. A modulated (flower-like) NH2-MIL-53 MOF increased the closed cell fraction whilst reducing cell size, with no effect on gas loss, whilst an unmodulated (cube like) NH2-MIL-53 MOF increased the gas loss without affecting cell size or closed cell percentage. Two further MOFs, Cu(BTetC)(DMF) and Cu(BDC)(DMF), were found to have no effect. This work therefore identifies Cu(ABDC)(DMF) as a promising additive for reducing gas-loss and maintaining the long-term performance in PIR foams, with its effectiveness demonstrated via an accelerated ageing technique developed for this study.
Polyurethane foams (PUF) utilised in the comfort industry generate substantial trim waste volumes requiring end-of-life management. Rebonding, one form of mechanical recycling, is a technique involving the mechanical breakdown and subse-quent adhesion of PUF using polyurethane prepolymers yielding a recycled material. However, the limited investigation into the properties of rebond PUF constrains its potential for novel alternative uses, such as soilless plant growing media, and new materials will need to be utilised to keep up with growing demand. Virgin PUF has been demonstrated to work as a growing media, so the recycling of current PUF waste into rebonds presents an opportunity to develop customisable up-valued materials for plant cultivation. A laboratory-scale rebond production method has been developed, and a series of re-bond PUF produced to evaluate the influence of crumb size, density, prepolymer chemistry and prepolymer loading on the properties of the rebond PUF and their suitability as growing media. Results indicated that higher quality rebonds were ob-tained with larger crumb sizes (mixed or > 7 mm), moderate amounts of prepolymer (4.5 to 7.5 % by mass) and higher den-sities. Density directly influenced plant growth-related properties, including airflow (which decreased with higher density), water uptake through wicking (which increased with density), and water retention through drainage (which increased with both density and larger crumb sizes [>7 mm]). These findings underscore density as a critical factor in the application of re-bonds as growing media. Eruca sativa plants were grown in three different rebonds at low, medium, and high density along-side a mineral wool control. Low density rebonds exhibited comparable growth (leaf length, leaf width and shoot fresh weight) to mineral wool, whereas medium and high density rebonds showed reduced growth. This study demonstrates the potential of rebond PUF foams as a viable growing media, which can be optimised using a laboratory-scale technique.
Polyurethane foams (PUFs) utilised in the comfort industry generate substantial trim waste volumes requiring end-of-life management. Rebonding, one form of mechanical recycling, is a technique involving the mechanical breakdown and subsequent adhesion of PUF using polyurethane prepolymers yielding a recycled material. However, the limited investigation into the properties of rebond PUF constrains its potential for novel alternative uses, such as soilless plant-growing media. A laboratory-scale rebond production method has been developed, and a series of rebond PUFs produced to evaluate the influence of crumb size, density, prepolymer chemistry, and prepolymer loading on the properties of the rebond PUFs and their suitability as growing media. The results indicated that higher quality rebonds were obtained with larger crumb sizes (mixed or >7 mm), moderate amounts of prepolymer (4.5 to 7.5% by mass), and higher densities. Increasing density directly influenced plant growth-related properties, including reducing airflow, increasing water uptake through wicking, and increasing water retention through drainage alongside larger crumb sizes [>7 mm]. To demonstrate the method’s utility for rapid screening, a plant growth trial was conducted using density as the key variable. Eruca sativa plants grown in low-density rebonds exhibited comparable growth (leaf length, leaf width, and shoot fresh weight) to mineral wool, whereas medium- and high-density rebonds showed reduced growth. This study validates a lab-scale technique that enables the rapid optimisation of rebond PUFs for novel applications like soilless growing media.