Inkjet printing is an excellent printing technique and an attractive alternative to conventional technologies for the production of flexible, low-cost microelectronic devices. Among many parameters that have a significant impact on the correctness of the printing process, the most important is ink viscosity. During the printing process, the ink is influenced by different strains and forces, which significantly change the printing results. The authors present a model and calculations referring to the shear rate of ink in an inkjet printer nozzle. Supporting experiments were conducted, proving the model assumptions for two different ink formulations: initial ink and with the addition of a dispersing agent. The most important findings are summarized by the process window regime of parameters, which is much broader for the inks with a dispersing agent. Such inks exhibit preferable viscosity, better print-ability, and higher path quality with lower resistivity. Presented results allow stating that proper, stable graphene inks adjusted for inkjet technique rheology must contain modifiers such as dispersing agents to be effectively printed.

Stretchable polymer composites are a new group of materials with a wide range of application possibilities in wearable electronics. The purpose of this study was to fabricate stretchable electroluminescent (EL) structures using developed polymer compositions, based on multiple different nanomaterials: luminophore nanopowders, dielectric, carbon nanotubes, and conductive platelets. The multi-layered EL structures have been printed directly on textiles using screen printing technology. During research, the appropriate rheological properties of the developed composite pastes, and their suitability for printed electronics, have been confirmed. The structure that has been created from the developed materials has been tested in terms of its mechanical strength and resistance to washing or ironing.

The authors explore the development of paper-based electronics using carbon-based composites with a biodegradable matrix based on ethyl cellulose and dibasic ester solvent. The main focus is on screen-printing techniques for creating flexible, eco-friendly electronic devices. This research evaluates the printability with the rheological measurements, electrical properties, flexibility, and adhesion of these composites, considering various compositions, including graphene, graphite, and carbon black. The study finds that certain compositions offer sheet resistance below 1 kΩ/sq and good adhesion to paper substrates with just one layer of screen printing, demonstrating the potential for commercial applications, such as single-use electronics, flexible heaters, etc. The study also shows the impact of cyclic bending on the electrical parameters of the prepared layers. This research emphasizes the importance of the biodegradability of the matrix, contributing to the field of sustainable electronics. Overall, this study provides insights into developing environmentally friendly, flexible electronic components, highlighting the role of biodegradable materials in this evolving industry.

Nerve regeneration through cell electrostimulation will become a key finding in regenerative medicine. The procedure will provide a wide range of applications, especially in body reconstruction, artificial organs or nerve prostheses. Other than in the case of the conventional polystyrene substrates, the application of the current flow in the cell substrate stimulates the cell growth and mobility, supports the synaptogenesis, and increases the average length of neuron nerve fibres. The indirect electrical cell stimulation requires a non-toxic, highly electrically conductive substrate material enabling a precise and effective cell electrostimulation. The process can be successfully performed with the use of the graphene nanoplatelets (GNPs)—the structures of high conductivity and biocompatible with mammalian NE-4C neural stem cells used in the study. One of the complications with the production of inks using GNPs is their agglomeration, which significantly hampers the quality of the produced coatings. Therefore, the selection of the proper amount of the surfactant is paramount to achieve a high-quality substrate. The article presents the results of the research into the material manufacturing used in the cell electrostimulation. The outcomes allow for the establishment of the proper amount of the surfactant to achieve both high conductivity and quality of the coating, which could be used not only in electronics, but also—due to its biocompatibility—fruitfully applied to the cell electrostimulation.

Ninety percent of high temperature electronic devices operate in temperatures in the range of 150 to 300 °C, and for such temperature needs, technologies typical for the military range might be adapted. To make it possible, new joining techniques are developed, one of them is use of pastes with silver nanoparticles sintered with low temperature joining technique. Silver sintered joints have three times higher thermal conductivity and five times lower electrical resistivity than typical solders, while being able to operate in temperatures reaching 350 °C. In this paper, the authors show the impact of additions of carbon nanoparticles on joints prepared in low temperature joining technology (LTJT). The authors prove that an addition of few percent of graphene nanoplatelets (GNPs) or carbon nanotubes (CNTs) improves joints mechanical, thermal, and electrical properties, while ensuring proper rheology of pastes.

Spinal cord injuries and neurodegenerative diseases, including Parkinson’s, Alzheimer’s, and traumatic brain injuries, remain challenging to treat. Nowadays, neural stem cell therapies excite high expectations within academia. The increasing demand for innovative solutions in regenerative medicine has drawn considerable attention to graphene materials. Due to unique properties, carbon materials are increasingly used as cellular scaffolds. They provide a biological microenvironment supporting cell adhesion and proliferation. The topography and mechanical properties of the graphene culture surface influence the forces exerted by the cells on their extracellular matrix. Which consequently affects the cell proliferation and differentiation. As a result, material properties such as stiffness, elasticity and mechanical strength play an important role in stem cells’ growth and life. The ink unification process is crucial while the layer homogeneity is essential for obtaining suitable surface for specific cell growth. Different ink unification processes were tested to achieve appropriate layer homogeneity and resistivity to successfully applied the GNPs layers in neural cell electrostimulation. The GNP coatings were then used to electrostimulate mouse NE-4C neural stem cells. In this study, the authors investigated how the stimulation voltage amplitude’s value affects cell behaviour, particularly the number of cells. Sinusoidal alternating current was used for stimulation. Three different values of stimulation voltage amplitude were investigated: 5, 10, and 15 V. It was noticed that a lower stimulation voltage amplitude had the most favourable effect on the stem cell count.