Multispectral thermometry is based on the law of blackbody radiation and is widely used in engineering practice today. Temperature values can be inferred from radiation intensity and multiple sets of wavelengths. Multispectral thermometry eliminates the requirements for single-spectral and spectral similarity, which are associated with two-colour thermometry. In the process of multispectral temperature inversion, the solution of spectral emissivity and multispectral data processing can be seen as the keys to accurate thermometry. At present, spectral emissivity is most commonly estimated using assumption models. When an assumption model closely matches an actual situation, the inversion of the temperature and the accuracy of spectral emissivity are both very high; however, when the two are not closely matched, the inversion result is very different from the actual situation. Assumption models of spectral emissivity exhibit drawbacks when used for thermometry of a complex material, or any material whose properties dynamically change during a combustion process. To address the above problems, in the present study, we developed a multispectral thermometry method based on optimisation ideas. This method involves analysing connections between measured temperatures of each channel in a multispectral temperature inversion process; it also makes use of correlations between multispectral signals at different temperatures. In short, we established a multivariate temperature difference correlation function based on the principles of multispectral radiometric thermometry, using information correlations between data for each channel in a temperature inversion process. We then established a high-precision thermometry model by optimising the correlation function and correcting any measurement errors. This method simplifies the modelling process so that it becomes an optimisation problem of the temperature difference function. This also removes the need to assume the relationships between spectral emissivity and other physical quantities, simplifying the process of multispectral thermometry. Finally, this involves correction of the spectral data so that any impact of measurement error on the thermometry is reduced. In order to verify the feasibility and reliability of the method, a simple eight-channel multispectral thermometry device was used for experimental validation, in which the temperature emitted from a blackbody furnace was identified as the standard value. In addition, spectral data from the 468–603 nm band were calibrated within a temperature range of 1923.15–2273.15 K, resulting in multispectral thermometry based on optimisation principles with an error rate of around 0.3% and a temperature calculation time of less than 3 s. The achieved level of inversion accuracy was better than that obtained using either a secondary measurement method (SMM) or a neural network method, and the calculation speed achieved was considerably faster than that obtained using the SMM method.

In the process of X-ray digital imaging, due to the mutual occlusion of object structures of different depth layers, the image projection information is overlapped. X-CT(Computed-Tomography) and X-CL(Computed-Laminography) are usually used to obtain structural information of objects at different depths, but they are limited by accurate multi-dimensional motion control systems, complex scanning methods and poor real-time computing performance.To solve the problems, this paper proposed a method of X-ray layered imaging based on linear scanning. This method only needs the object to pass through the detection area along a straight line to realize the multi-view imaging, extracts the effective multi-view images information for refocusing imaging, and realizes the reconstruction of different depth layers of the object. Meanwhile, the automatic marking matting algorithm is employed to remove the non-focused interference in the refocused images. Experiments of X-ray layered imaging were conducted, which demonstrated the proposed method can achieve objects reconstruction with different depths, and effectively remove the non-focused interference.

High-precision source localization depends on many factors, including a suitable location method. Beamforming-based methods, such as the steered response power (SRP), are a common type of acoustic localization methods. However, these methods have low spatial resolution. The SRP method with phase transform (SRP-PHAT) improves the spatial resolution of SRP and is one of the most effective and robust methods for source localization. However, the introduction of a phase transform to SRP might amplify the power of the noise and result in many local extrema in the SRP space, which has a negative impact on source localization. In this paper, a steered sample algorithm (SSA) based on the reciprocity of wave propagation for acoustic source localization is proposed. The SSA localization process is similar to the hyperbolic Radon transform, which is theoretically analyzed and is the most essential difference form the SRP/SRP-PHAT. Compared with the SRP-PHAT, the experimental results demonstrate that the SSA perform better when it comes to array signal positioning with limited array elements and narrow azimuth signal, where SSA can achieve high precision positioning with lower SNR.

Quantitative analysis of the flow field is an effective method to study hydrodynamics. As a flow field measurement technology, the Background Oriented Schlieren (BOS) is widely used. However, it is difficult to measure the complex transparent flow field (flow field with large refractive index gradient) using the BOS experiment. In order to overcome this difficulty and improve the accuracy of the BOS experiment, this paper presents a hybrid adaptive wavelet-based optical flow algorithm for the BOS. The current algorithm is a combination of the traditional optical flow algorithm and the wavelet-based optical flow algorithm. By adding the initial value constraints, the adaptive scale constraints, and the adaptive regularization constraints, the algorithm can effectively overcome the above-mentioned difficulty and also improve its accuracy. To further illustrate the feasibility of the proposed method, this paper uses the simulation data, the data of the DNS datasets, and the data of the BOS experiment to verify the performance of the algorithm. The experiment of comparing the proposed algorithm with the existing ones is carried out on the DNS datasets and the data of the BOS experiment. Finally, the proposed method is verified by a practical BOS experiment. The results show that the proposed algorithm can effectively improve the measurement accuracy of displacements.

Synthetic aperture imaging (SAI) technology gets the light field information of the scene through the camera array. With the large virtual aperture, it can effectively acquire the information of the partially occluded object in the scene, and then we can focus on the arbitrary target plane corresponding to the reference perspective through the refocus algorithm. Meanwhile, objects that deviate from the plane will be blurred to varying degrees. However, when the object to be reconstructed in the scene is occluded by the complex foreground, the optical field information of the target cannot be effectively detected due to the limitation of the linear array. In order to deal with these problems, this paper proposes a nonlinear SAI method. This method can obtain the occluded object’s light field information reliably by using the nonlinear array. Experiments are designed for the nonlinear SAI, and refocusing is performed for the occluded objects with different camera arrays, different depths, and different distribution intervals. The results demonstrate that the method proposed in this paper is advanced than the traditional SAI method based on linear array.